background image

650483-000 Rev. B 07/15 • Page 10 of 10

Status Indicator Codes

Table 2: Status Indicator Codes for Push-to-Test Switch (when AC is present)

Status Indication

Status Description

Status Definition

No light

AC power removed from circuit

*

Continuous steady light

Battery fully charged

*_*_

Light blinks 1 time

Battery charging

**_**_

Light blinks 2 times

Battery failure

***_***_

Light blinks 3 times

LED lamp head failure

****_****_

Light blinks 4 times

Emergency circuit charger board failure

= Status LED ON; 

= Status LED OFF

Maintenance

Battery

•  The unit uses a sealed, NiCD battery which requires no maintenance. For replacement, contact the factory.

Tests

• 

Monthly:

 The unit will automatically test the operation of the emergency circuit (for 30 seconds minimum) once a month.  

The emergency lamps will illuminate during the test. See “Self-Diagnostic Testing” for further information.

• 

Once a Year:

 Conduct a 90-minute discharge test once a year. The lamps should operate for at least 90 minutes.

Replacement Parts

Emergency Lighting Unit

• 

Driver Board Kit:

 N2LEDCB.

• 

Battery Pack Kit:

 N2LEDBP.

• 

Nickel-Plated Brass M25 Male, 3/4 in. NPT Female Hub:

 737DM7T25.

Lighting Fixture Head Assembly

• 

Light Head Kit:

 N2LEDLH. 

NOTE: 

If the LED fails, the entire assembly must be replaced.

Except as expressly provided by Appleton Grp, LLC (Appleton), Appleton products are intended for ultimate purchase by industrial users and for operation by persons trained and experienced in the use and maintenance of this equipment
and not for consumers or consumer use. Appleton warranties DO NOT extend to, and no reseller is authorized to extend Appleton’s warranties to any consumer.
While every precaution has been taken to ensure accuracy and completeness in this manual, Appleton Grp, LLC. assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or
omissions. Specifications are subject to change without notice. The Appleton and Emerson logos are registered in the U.S. Patent and Trademark Office. All other product or service names are the property of their registered owners.
©2015 Appleton Grp, LLC. All rights reserved.

Содержание N2LED Series











Отзывы: