Applent Instruments AT520 Скачать руководство пользователя страница 21

Страница: 21 / 40

Comparator 21

Comparator

This chapter describes how to configure AT520x comparator.
Include:



Turn ON/OFF Comparator



Setup the comparator record number



Setup Comparator

5.1

Turn

ON/OFF

the

Comparator

Step1: Under measurement mode
Step2: Press Comp key to toggles the comparator ON and OFF.

“COMP” appears lit on the VFD when the comparator is on.
“COMP” is not lit, the comparator function does not execute.

5.2

Setup

the

record

number

and

comparator

Step1: Press Shift Comparator to the setup comparator.
Step2: Rec.09 indicator at the lower right corner of screen flashes means you can setup record

number.

Step3: Press < > or Knob to choose the record number from 1 to 30.
Step4: You

can

a) Press Enter key to enter the comparator state to setup nominal value and limit value.
b) Or press Esc to exit from comparator setup and the record number is stored.

Step5: Press Shift Comparator to setup comparator.
Step6: Press > or knob to choose the resistance’s nominal value (1

line), upper limit value (2nd

line), lower limit (3

line).

Step7: Press digits to input value
Step8: Press Enter or Shift + n/



/m/k/M/G to key in the unit.

Note: Enter stand for x1 unit.

Step9: Press > or knob again to choose next voltage setup page

Step10: Input number and key in the unit

Step11: Press ESC to end setup.

5.3

Setup

Beeper

Step1: Press Shift Comparator to enter Beeper setup window.
Step2: Press< > key or Turn Knob to choose following items:

Beep

while

pass.

Beep

while

fail.

Содержание AT520









































Результаты поиска

Содержание AT520

Отзывы:

Бренды по названию

Популярные бренды

Applent Instruments AT520, Руководство пользователя

Результаты поиска

Содержание AT520

Отзывы:

Бренды по названию

Популярные бренды