APPA 76 Скачать руководство пользователя страница 17

Страница: 17 / 22

FUSE REPLACEMENT

To change or check the fuse, refer to Fig.3 and follow the instructions given below.

1. Carry out steps 1 to 3 of the instructions for changing the battery.

2. Lift the printed circuit board out of the top half of the case. Do not unscrew any of the screws in the printed

circuit board.

3. Carefully remove the fuse from the fuse holder by first levering one end out of one clip and then pulling the fuse

out of the other clip.

4. Fit a new fuse of the same size with the same ratings. Make sure that the fuse is centered longitudinally in the

fuse holder.

5. Make sure that the bar of the rotary switch in the top half of the case and the rotary switch on the printed circuit

board are both in the "OFF" position.

6. Fit the printed circuit board back into its original position, making sure that O-rings on the case screws are

correctly seated and that the connecting wire of the battery will not be caught between the top and bottom

halves of the case. Fit the two halves of the case back together ensuring that the notches in the top half of the

case are engaged. Screw the three screws back in.

Содержание 76























Результаты поиска

Содержание 76

Отзывы:

Похожие инструкции для 76

Бренды по названию

Популярные бренды

APPA 76, Инструкция по эксплуатации

Результаты поиска

Содержание 76

Отзывы:

Похожие инструкции для 76

Бренды по названию

Популярные бренды