Apollo SA7100-100APO Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 24

background image

4. Address Settings

Select the required address using address switches 1 to 7 for XP/Discovery and 1 to 8 for

Soteria with core enabled panel. The reference table can be viewed below, addresses 127-254

relate only to Soteria. When only one detector is connected it will appear on the address set on

the DIP switch. When there are two detectors connected then detector 1 will appear on the

selected address and detector two will appear on the selected a1.

5

«
...
3
4
5
6
7
...
»

Содержание SA7100-100APO

























Отзывы:

Нет отзывов

Похожие инструкции для SA7100-100APO

Бренд: Magnadyne Страницы: 20

Бренд: jablotron Страницы: 8

Бренд: S&S Страницы: 12

Бренд: X10 Страницы: 4

Бренд: Uniden Страницы: 12

Бренд: Swann Страницы: 8

Бренд: Channel Vision Страницы: 2

Бренд: Fike Страницы: 4

Бренд: Dahua Страницы: 16

Бренд: Axis Страницы: 7

IPC-HDW3549H-ZAS-PV-27135

Бренд: Dahua Technology Страницы: 17

eyeWAVE RWX95CMP

Бренд: Risco Страницы: 2

Бренд: Sennco Solutions Страницы: 23

Бренд: Dahua Technology Страницы: 22

IDCMR-ALG-OZ-IC-1080P

Бренд: Larson Electronics Страницы: 6

Бренд: SenseTek Страницы: 44

Бренд: GeoVision Страницы: 8

Бренд: HIKVISION Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды