background image

IMPORTANT - READ CAREFULLY BEFORE BEGINNING INSTALLATION 

 

WARNING—To reduce the risk of injury or death: 

 

Read this installation manual completely prior to installation. 

Installation should be performed by a professional installer. 

Required welding should be performed by a qualified welder. 

Should electricity be required, use a certified electrician only. 

Any device that requires 120 Volts AC should be U.L. approved. 

Review with the owner all safety concerns including: 

 

Do not operate the gate unless area around gate is in full view. 

Do not allow children or adults to “ride” on gate during operation. 

Do not allow children to play in the gate area. 

Periodically test the obstruction sensitivity to assure safe and 
proper operation. **Do not test sensitivity by standing between the 
gate and the hinge or stop post.
 

Keep the remote control away from children. 

The “CAUTION AUTOMATIC GATE” sign should be clearly visible 
from both sides of the gate. 

Always insure that the gate has closed securely before leaving 
area. 

Arrange with local fire and law enforcement for emergency access. 

Always keep people and objects away from the gate. No person 
should cross the path of the moving gate. 

 

Recommend safety devices such as loop detectors, edge switches, and 
beam detectors when applicable. 

Install control devices such as keypads far enough away (5 feet or further) 
from any moving parts of the operator and gate to prevent possible injury. 

Always disconnect the battery or power source when making adjustments 
or repairs to any part of the gate or operator. 

All rollers should be covered to prevent injury. 

 
Test the gate operator monthly.  The gate must reverse on contact with a rigid 
object or stop when an object activates the non contact sensors. After adjust-
ing the force or limit of travel, retest the gate operator.  Failure to adjust and 
retest the gate operator properly can increase the risk of injury or death. 

IMPORTANT SAFETY PRECAUTIONS 

Содержание 7100UL


















Отзывы: