Apex Digital Pro MXR 100 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 18

Apex Digital Pro MXR 100 Скачать руководство пользователя страница 15

- -

14

Troubleshooting

Engine does not start

No fuel flow to carburetor

No fuel in fuel tank
Clogged float valve
Clogged fuel tank cap breather hole
Clogged fuel tube

Weak or no spark

Engine stop switch in OFF position
Ignition switch in OFF position
Safety tether switch disengaged
Faulty spark plug
Fouled spark plug
Faulty CDI unit
Faulty alternator
Faulty engine stop switch
Faulty ignition coil
Poorly connected, broken, or shorted wires
Broken or shorted spark plug wire
Faulty ignition switch

Low compression

Worn cylinder and piston rings
Damaged cylinder head gasket

Engine does not fire

Improperly adjusted air screw
Improper ignition timing
Fuel/air mixture ratio is too lean

Engine starts but dies

Fuel system

Fuel petcock not in ON position
Dirty or clogged fuel filter
Air cleaner dirty
Fuel/air mixture ratio is too lean
Improperly adjusted air screw
Carburetor flooded

Ignition system

Improper ignition timing
Faulty spark plug

«
...
13
14
15
16
17
...
»

Содержание Pro MXR 100



















Отзывы:

Нет отзывов