background image

June 2013 

10 

80-0180-347 Rev. A 

STEP 2     SPINDLE PREPARATION  

(For 1-3/4” doors) 

 

For  Adams  Rite  MS1850  Deadbolts,  4500/4900  Deadlatches,  & 
8000 Series Mortise Exit Devices

:   

Snap-off spindle at fifth (5th) notch as shown in  F

IG

.  4.   For 2” thick 

door add one notch. 
 

 

  

 
 

 
 
For Adams Rite 8600 Concealed Vertical Rod Exit Devices: 

  

Snap-off  spindle  at  sixth  (6th)  notch  as  shown  in  F

IG

.5.    For  2”  thick 

doors add two notches. 
 

 

 

 
 
 
 
 

For Adams Rite 8000 Series Surface Vertical Rod & Rim Exit  De-
vices, Yale  7200  Series    Narrow Stile  Exit Devices, Corbin  Russ-
win ED4000  Series, and SARGENT 8500 Narrow Design Rim Exit 
Devices: 

Snap-off spindle at fourteenth (14th) notch as shown in F

IG

6.  For 2” thick doors add two notches. 

F

IG

. 6

 

Insert “T”  
end into  

exit devices 

Fourteenth notch 

F

IG

. 5

 

Sixth notch 

Insert Flat  
end into  

exit devices 

F

IG

. 4

 

Fifth notch 

Insert Flat  
end into  

exit devices 

June 2013 

11 

80-0180-347 Rev. A 

STEP 3     CONFIGURE FOR LOCK SERIES 

 

Mortise Latch Application:  

A100-3090H for 4500/4900 

(including 8300/8400 Exit Devices) 

 
Configure the supplied cam plug to match the hand of door. Insert 
into latch case with notch on the cam plug aligned with latch case set 
screw.  Tighten set screw and secure with the two brass cam plug 
screws. 

 

 

 
 
 
 
 
 
 
 
 
 
 
 

 

 

CVR Exit Device Application:       
A100-3090H for 8500/8600 

Install Tailpiece adapter on the vertical rod and fasten with Phillips 
screw as shown. 

   
F

IG

. 9 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Note: Devices manufactured before 1997 will not accept the tail piece adapter 

 

 

Left Hand  

Reverse (LHR) 

F

IG

. 7 

Right Hand  

Reverse 

(RHR) 

F

IG

. 8 

Содержание eForce A100 A100-3090H











Отзывы: