manualshive.com logo in svg

Apeks XL4 SECOND STAGE, Техническое руководство по обслуживанию, Страница: 17 / 21

Поделиться
Скачать
Apeks XL4 SECOND STAGE Скачать руководство пользователя страница 17

LUBRICANT/CLEANER

APPLICATION

SOURCE

Christo-Lube® MCG 111

PerflouroLube 20/1

Lubricant for all o-rings

Aqua Lung, PN 820466, 

or

Lubrication Technologies 

310 Morton Street 

Jackson, OH  45640 

(800) 477-8704

Performance Fluids

Ste 101 Lomeshaye Business Park

Turner Road

Nelson Lancashire BBP 7DR

             

White distilled vinegar

(diluted with water)

Bath for reusable stainless 

steel and brass parts.

“Household” grade

Oxygen Compatible Solution

Promoclean TP108

Janitol Plus

Nitrox/O2 Cleaning

As Per Training

INVENTEC PERFORMANCE 

CHEMICALS SA.

20, Rue de bourgogne

BP 211

69802 SAINT-PRIEST cedex

JOHN LAWSON DIST.

SCOTSHAW BROOK HOUSE

BRANCH ROAD

LOWER DARWEN

LANCASHIRE  BB3 0PR

Liquid Dishwashing Detergent 

(diluted with warm water)

Degreaser for brass and stain-

less steel parts; general cleaning 

solution for plastic and rubber

“Household” grade

TABLE 5: RECOMMENDED CLEANERS & LUBRICANTS

CAUTION:

  Silicone rubber requires no lubrication or preservative treatment.  DO NOT apply grease or spray to silicone 

rubber parts.  Doing so may cause a chemical breakdown and premature deterioration of the material.

CAUTION:

  Do not use muriatic acid for the cleaning of any parts. Even if strongly diluted, muriatic acid can harm 

chrome plating and may leave a residue that is harmful to o-ring seals and other parts.

17

XL4 SECOND STAGE TECHNICAL MAINTENANCE MANUAL

Содержание XL4 SECOND STAGE






















Отзывы:

Нет отзывов