Apantac CP-16 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 24

Apantac CP-16 Скачать руководство пользователя страница 19

APANTAC LLC, 10200 SW Allen Blvd, Beaverton, OR 97005

[email protected]

, TEL: +1 503 968 3000

16

7.4.2

GPIO Control Setup



GPIO Button Mode

There are two options; GPO and AXP CMD.

GPO

When this option is selected the GPIO port on the back of the CP-16 is configured for output.

When buttons 1 through 8 are pressed the corresponding GPO wire on the port will go high

(5 Volts). Only the actively lit button will be high, the other GPO wires will be low (0

volts).

The AXP command for the button will also be sent via TCP/IP to the multiviewer. The GPO

output can be used to trigger any external equipment.

Apantac Tahoma Multiviewer's also have a GPIO port and the CP-16 GPO can be used to

trigger these inputs if desired. The multiviewer must be configured to respond to GPIO

inputs.

AXP CMD (GPI)

When this option is selected the GPIO port on the back of the CP-16 is configured for input.

An internal 5-volt source is provided through a 'pull-up' resistor. All inactive inputs of the

GPI port will be high.

When the corresponding GPO wire on the port is brought low (shorted to the port's ground

pin by an external relay or open-collector GPO of an external piece of equipment) the

corresponding button will be selected (buttons 1 through 8). The button will lite and the

command will be sent via TCP/IP to the multiviewer.

«
...
17
18
19
20
21
...
»

Содержание CP-16

























Отзывы:

Нет отзывов