AP Cumberland Feed-Link 2 Скачать руководство пользователя | Manualshive

Страница: 34 / 46

background image

9. RF Module Option

34

PNEG-2340

Feed-Link 2

Connect Wires to a Network Master

Connect the power cable to “24 VDC” terminal strip on the back right hand side of the Network Master.
Connect the white wire from the power cable to the terminal marked “24 VDC +”. Connect the black wire
to the terminal marked “24 VDC -”. Connect RS485 communication cable to “RS485” out terminal strip on
the black center of the Network Master. Connect the white wire from RS485 cable to the terminal marked
“A”. Connect the black wire to the terminal marked “B”. Connect GND (shield) wire to the terminal marked
“Shield”.

(See Figure 9D.)

The RF module that is connected to the Network Master either directly or in the daisy chain is considered
the “Server”, so dip switch 6 on the left bank should be ON. All RF modules are setup as “Client” out of the
box. This default setup has dip switch 6 on the left bank in the OFF position and is used for the remote bins.

Figure 9D Network Master and RF Module Wiring Diagram

«
...
32
33
34
35
36
...
»

Содержание Cumberland Feed-Link 2















































Отзывы:

Нет отзывов

Похожие инструкции для Cumberland Feed-Link 2

imageRUNNER ADVANCE C9075S PRO

Бренд: Canon Страницы: 20

Бренд: Wasp Страницы: 16

Бренд: D-Link Страницы: 40

Бренд: Taie Страницы: 66

Бренд: XGAMING Страницы: 9

Бренд: V2 ELETTRONICA Страницы: 72

Бренд: KIPI Страницы: 44

Бренд: Gallagher Страницы: 2

Бренд: baby joy Страницы: 11

Бренд: Simplex Страницы: 40

Бренд: Euromatic Страницы: 20

Бренд: VMK Страницы: 98

AQUIS ULTRAFLOW

Бренд: Waterous Страницы: 217

Бренд: Mosa Страницы: 28

Hydropan-Single

Бренд: ETNA Страницы: 12

Explorer Dongle

Бренд: Sparkfun Electronics Страницы: 16

R1000 series E20

Бренд: Roland Страницы: 156

Бренд: Bandini Industrie Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды