ASLINKTERMINAL
[ASLINK Small Integrated 16-Point Terminal]
AnyWireASLINK System Products Guide
BL296
□
B-16F
□
-4A-20
The
Products Guide
describes individual products. Refer to the Guide as necessary.
■
Function List
-BL296*B16F*4A20 1/11-
Connection targets
I/O
short
circuit
Specifications
Model
I/O
disconnection
ASLINKTERMINAL
four-wire
(isolated) cable
type
NPN 16-point input/16-point output
PNP 16-point input/16-point output
NPN 8-point input/8-point output (hybrid)
PNP 8-point input/8-point output (hybrid)
Universal sensors
and switches,
universal output
devices
Small-
sized
Sensing
level
reduction
I/O
power supply
reduction
Slave unit
voltage
reduction
[Warranty]
[Notes on Safety]
Precautions that must be observed in order to use this system safely are indicated as shown below.
You must observe these precautions.
WARNING
CAUTION
A WARNING indicates a potentially hazardous
situation which, if not handled correctly, could
result in death or serious injury.
A CAUTION indicates a potentially hazardous situation
which, if not handled correctly, may result in personal
injury or property damage.
WARNING
○
System Safety
○
Always turn off the power before attempting to mount or replace.
This system is intended for general industrial applications. It does not have functions for supporting applications requiring higher
levels of safety such as safety-related devices or accident prevention systems. The product must not be used for these purposes.
○
Prolonged continuous flow of a rated load current or higher or a transit current due to load short-circuit, etc., in the hybrid unit including
the output unit and the output circuit may result in smoking or firing. An external safety device such as a fuse must be installed.
○
Use the
AnyWireASLINK
within the range of the specifications and conditions shown below.
○
System power supply
○
Separately route high-voltage and power cables
○
Connectors and terminals
○
Do not impose any external loads on the units. Doing so may cause a failure.
○
Do not disconnect or reconnect between the transmission line and slave units. A malfunction may occur.
Use a stable, 24V DC power supply. Use of an unstable power supply may cause problems with the system.
Although the
AnyWireASLINK
has a high noise margin, keep the transmission line and I/O cables away from high-voltage and
power cables.
* Pay careful attention to the length and installation of cable wiring to ensure that connectors and cables are neither overloaded nor disconnected.
* Make sure to prevent any metal objects from getting inside the connectors or the terminal blocks.
* Short-circuits caused by metal objects or mis-wiring are likely to damage the device.
CAUTION
■
Warranty period
The warranty on the delivered Product shall continue to be effective for one (1) year after the delivery thereof to a location as
designated by the original owner.
■
Scope of warranty
Should a defect occur in any part of the Product during the foregoing warranty period when it is used normally in acordance with
the specifications described in this User's Manual, the Company shall replace or repair the defect free of charge, except when it
arises as a result of:
[1] Misuse or abuse of the Product by the owner;
[2] Fault caused by other than the delivered Product;
[3] The unauthorized modification or repair of the Product by any person other than the Company's personnel;
[4] Any unusual force of nature, disaster or other cause beyond the Company's control.
The term "warranty," as used herein, refers to the warranty applicable to the delivered product alone. The Company shall not be
liable for consequential or incidental damages resulting from any malfunction.
■
Repair at cost
After the expiration of the warranty period, the owner shall be responsible for all costs and expenses incurred for the trouble-
shooting and repair of the Product. Even during the warranty term, the Company shall repair any defects arising from causes
other than within the scope of the warranty as specified above, at the owner's cost.
■
Notes on use
⇒
To set any address, an “Address writer ARW-04 (Ver. 04-1.01 or higher), ARW-03 (Ver. 2.10 or higher)”
is required. Please prepare it separately.
[Type]
BL296SB-16F-4A-20
BL296PB-16F-4A-20
BL296XB-16F-4A-20
NPN input
NPN output
NPN input/NPN output
BL296SB-16FS-4A-20
BL296PB-16FS-4A-20
BL296XB-16FS-4A-20
PNP input
PNP output
PNP input/PNP output
○
×
○
○
×
×
Functions
