background image

Page 3

CLEANING

1.  It is advisable to clean the interior of the machine as often as  

     possible to maintain good hygiene standards.

2.  Always ensure that the unit is disconnected from the main power 

     supply before cleaning.

3.  Do not use abrasive powders or solvents to clean this unit.

4.  The unit should be cleaned with warm soapy water. Use only a 

     damp cloth. 
5.  Dry the unit carefully with a cloth before turning back on.
6.  

IT IS ESSENTIAL THAT THE COOLING CONDENSOR IS CLEANED   

     ON A REGULAR BASIS TO ENSURE OPTIMUM PERFORMANCE OF  

     THE UNIT.

     THE CONDENSOR IS ACCESSIBLE BY REMOVING THE ACCESS 

     PANEL BELOW THE CONTROLLER. 

     A DUST FILTER IS FITTED IN FRONT OF THE CONDENSOR, THIS 

     IS REMOVED BY LOOSENING THE SCREW AT THE TOP CENTER  

     AND LIFTING OUT. THIS FILTER MAY BE WASHED WITH WARM 

     SOAPY WATER, AND ALLOWED TO DRY BEFORE REFITTING.

     THE CONDENSOR MAY BE CLEANED CAREFULLY WITH A 

     SUITABLE SOFT BRUSH OR COMPRESSED AIR IF POSSIBLE

.

THE UNIT SHOULD NEVER BE CLEANED USING A WATER JET 

OR SIMILAR PRESSURE CLEANING DEVICE.

SAFETY:

 

1.  The units are designed to operate on alternating current only 

     (A.C.). DO NOT CONNECT TO DIRECT CURRENT (D.C.).

2.  Ensure that the power supply cord does not come into contact 

     with hot surfaces.

3.  If the supply cord is damaged,it must be relaced with a new cord 

     assembly available from the suppliers agent.

4.  Do not use the unit in a dusty enviroment or in and explosive 

     atmosphere.

5.  This unit is designed for indoor use only

6.  BASIC SAFETY RULES

     a.  Do not touch the unit when hands and feet are wet

     b.  Do not use the unit when bare foot

     c.  The unit should never be used by children or untrained 

          personnel

     d.  Do not pull on the electrical cord when unplugging the 

          machine.

Page 4

DESCRIPTION OF MODELS

MODEL

DESCRIPTION CAPACITY VOLTAGE

( V/Hz)

POWER

( WATTS)

CDF2001

CAKE DISPLAY 

FRIDGE

500L

230/50

905

CDF2001-120V

CAKE DISPLAY 

FRIDGE

500L

120/60

905

CAKE FRIDGE WIRING LEGEND

LEGEND

 DESCRIPTION

PART NUMBER

F1

 FUSE

1-15-FU

S1

 LIGHT SWITCH

XCDF1019

S2

 DEFROST SWITCH

XCDF1019

S3

 REFRIGERATION SWITCH

XCDF1019

DS1

 DOOR SWITCH

XCDF1012

L1

 INTERIOR LIGHT

N-A

H1 

 DEFROST HEATER

1-DH-CDF2001

M1

 EVAPORATOR FAN

XCDF1016

M2

 MOTOR ROTATING SHELVES

XCDF1020

M3

 CONDENSOR MOTOR

XCDF1022

M4

 COMPRESSOR

XCDF1017

R1&R2

 RELAY

1-RELAY-CDF2001

EC1

 ELECTRONIC CONTROL

XCDF1027

T1 

 DEFROST HEATER TRANSFORMER

XCDF1018

T2

 ELECTRONIC CONTROL TRANSFORMER

XCDF1027

TR1

 TEMPERATURE PROBE

XCDF1027

TR2

 DEFROST PROBE

XCDF1027

Содержание CDF2001







Отзывы: