background image

®

P/N 1011436 Rev. H 02/21

7

Operating Instructions

1. 

Set the Bun Thickness Adjustment 

Controls (Figure 4).

NOTE:

 Your individual customer or 

store requirements are the 

deciding factor on the finished 

product, not the Bun Thickness 

setting.

NOTE:

 The default Bun Thickness 

settings are 2 for Crown Front 

and 2 for Heel Rear, but settings 

are adjustable from 1-6. It is 

acceptable to adjust the Bun 

Thickness setting as needed 

to achieve the desired quality 

toast and bun compression.

2. 

Turn the power on and wait until the 

display reads USE before proceeding.

NOTE:

 The display (Figure 4) flashes 

“LO” during warm-up. “USE” 

appears when the toaster is 

ready for use.

3. 

Fill the Butter Pan (Mfg. No. 9210914 

only).

4. 

Slide buns across the rotating Butter 

Wheel with the cut face down (Mfg. 

No. 9210914 only). Drop buns into the 

Bun Feeder. Insert buns so they face 

the center platen.  The cut sides of 

heel and crown must face each other 

and slide against the Release Sheet 

with Crowns inserted in the front and 

Heels inserted in the rear.

5. 

Toasted buns drop onto the Bun 

Chute (Figure 4).

6. 

Test at least 4 buns before putting the 

toaster into service.

Default Settings

Recommended temperatures

The default and recommended 

temperature setting for the A platen heater 

is 293° C (560° F).
The default and recommended 

temperature setting for the B Platen heater 

is 218° C (424° F).

Recommended Speed Setting

The default and recommended speed 

setting is 1400 for 22 second pass-through 

(plus or minus 2 seconds).

Light/Dark Setting

The toaster has a Light/Dark adjustment 

setting that allows you to adjust the toast 

quality as the toaster is running.
While the toaster is in USE mode, press 

the UP or Down arrow buttons to adjust the 

Light/Dark setting. 
The default setting is D0. 
Light 10  is the lightest setting
Dark 10 is the darkest setting.

Butter Wheel and Pan 

(Mfg. No. 9210913)

Bun Thickness 

Adjustment 

Control (Heel)

Temperature 

Controls & 

Temperature 

Display

Bun Thickness 

Adjustment 

Control 

(Crown)

Bun Chute

Hi-Limit 

Reset

Power 

Cord

Figure 4. VCTM-2 Toaster

Содержание 9210914

























Отзывы: