7
P/N 1011190 Rev. G 01/17
DAILY CLEANING
1. Turn the toaster’s power switch to
the off position. The toaster enters
a 45 minute cool-down mode and
automatically shuts down when
complete.
NOTE:
Be sure to perform cleaning
steps during cool-down mode.
2. Put on neoprene gloves and
remove the Bun Feeder and the
Butter Wheel.
3. Clean the outside surfaces of the
toaster with a paper towel sprayed
with an approved multi-surface
cleaner. Allow to air dry.
4. Wipe the Bun Feeder Assembly with
a paper towel sprayed with an ap-
proved multi-surface cleaner. Allow
to air dry.
5. Wash, rinse, and sanitize the Bun
Wheel assembly at the sink and
allow to air dry.
6. Remove the Front and Rear Con-
veyor Covers by lifting up and away
from the unit.
NOTE:
Replace all Belts if any of the
Belts are discolored, torn, or if
any of the Belt Snaps are dam-
aged.
NOTE:
Only clean the rear Belt when it
is in front of the Backing Plate.
This avoids causing damage to
the Belt. The conveyors continue
to turn during the cool-down
period.
7. Inspect the front and rear Belts. Re-
place all of the belts if any of them
are torn, folded, discolored, missing
snaps, or damaged in any way.
8. If the Belts are all in good condition,
spray a clean, sanitized towel with
an approved sanitizer. Press and
hold both arrow buttons for 5 sec-
onds. PUR appears on the display
with a blinking cursor. This locks
the belt speed in Purge mode for 5
minutes to assist in cleaning. Wipe
the front and rear Belts clean. Allow
to air dry.
9. Press any button to exit Purge
mode.
NOTE:
Only clean the Belt where it is in
front of the Backing Plate. This
avoids causing damage to the
Belt.
10. Clean the Front and Rear Conveyor
Covers with a paper towel sprayed
with an approved multi surface
Cleaner. Allow to air dry.
11. Reinstall the Front and Rear Con-
veyor Covers and then re-install
the Bun Feeder and Butter Wheel
assemblies.
12. Re-fill the Butter Wheel pan.
13. Turn the toaster on and test the unit
before returning it to operation.
NOTE:
These cleaning steps may need
to be repeated to remove heavy
carbon buildup.
NOTE:
Be sure to clean and sanitize
the Belts completely. Failure
to properly clean the Belts will
shorten the life of the Belts and
result in poor toaster perfor-
mance.
NOTE:
Replace all Belts if any of the
Belts are discolored, torn, or
if any of the Belt Snaps are
damaged. To obtain new Belts,
contact the factory at 1-877-
392-7854 (North America only)
or 630-784-1000.
NOTE:
Belts should be removed ONLY
during Belt replacement or
when required in a service situa-
tion.
REPLACING BELTS
(QUARTERLY)
Over time, the Belts begin to show signs of
wear. This wear appears in the form of tears
or discoloration of the belt, at which point
all belts should be replaced.
NOTE:
Belts should be removed ONLY
during Belt Replacement or
when required in a service situ-
ation. For proper operation, re-
place all belts at the same time.
Removing Belts
1. Turn the toaster off’s power switch
to the off position. The toaster
enters a cool-down mode and will
automatically shut down when
complete.
2. Unplug the power cord once the
cool-down period is complete.
3. Put on neoprene gloves. Remove
the Bun Feeder.
4. Remove the Front and Rear Con-
veyor Covers by lifting up and away
from the toaster.
5. Set the Compression Knob from 4
to 7.
6. Unlock the latch and open the left
side panel.
7. To lock out the front Conveyor
Roller, face the front of the toaster.
Use both hands and push down on
the Front Conveyor Roller and pull
towards you. This removes tension
and locks the roller in place.
8. To lock out the Rear Roller, face the
rear of the toaster. Use both hands
and push down on the Rear Con-
veyor Roller and push away from
you. This removes tension and locks
the roller in place.
9. Lift the upper Belt Frame Lock. Then
rotate down so it rests on the cam
shaft of the rear conveyor roller.
10. Pull down the lower Belt Frame
Lock.
11. Using a utility knife, cut the existing
Front Belts and remove from the
toaster. Discard the old Belts.
12. Using a utility knife, cut the Rear
Belt and remove from the toaster.
Discard the old Belt.
Installing Belts
NOTE:
To obtain new Belts, contact
the factory at 1-877-392-7854
(North America only) or 630-
784-1000.
1. Follow the steps for Removing Belts.
2. Wipe both sides of the new Belts
with a clean, sanitized towel
sprayed with an approved sanitizer
and allow to air dry.
3. Slide the new rear belt gently over
the rear top roller and rear bottom
roller.
NOTE:
Make sure the belt lines up
properly on the rollers. The
snaps on the belts should face
the inside of the top front roller.
4. Slide the Heel/Texas Toaster belt
over the front bottom roller. Repeat
this step for the crown belt.
NOTE:
Make sure the belt lines up
properly on the rollers. The
snaps on the belts should face
the inside of the top rear roller.
Belts must be installed so the
exposed diagonal seam of the
belt is away from the direction
of belt travel.
5. Return the Front and Rear Belt Roll-
ers to full tension by sliding them
toward each other so each roller
locks into place.
6. Slowly lift up the Lower Belt Frame
Lock so the Front and Rear Belt Roll-
ers lock into place.
Содержание 9210875
Страница 17: ...17 P N 1011190 Rev G 01 17 WIRING DIAGRAM ...
Страница 18: ...18 P N 1011190 Rev G 01 17 NOTES ...
Страница 19: ...19 P N 1011190 Rev G 01 17 NOTES continued ...
