HEBT-5V BUN TOASTER
8
P/N 1011112 Rev W 05/22
McDonald’s
Control Panel LEDs
The LEDs on the control panel light to signify when each item
is operating. The Service LED lights and the corresponding
LED (Motor, A Platen, B Platen, C Platen) blinks when the unit
requires service. A message also appears on the display.
Settings
Follow these steps to view and adjust toaster settings:
1.
When the unit is plugged in, press and hold the
MENU
button (Figure 5) for five seconds. The control panel
displays “A Platen.” The display scrolls to show the actual
temperature, SSR Duty cycle, and the setpoint.
Example:
A Platen: 271°C 35% 271°C
NOTE:
The unit does not have to be turned on in order to
access the settings menu.
2.
Use the
LEFT
and
RIGHT
arrow buttons (Figure 4) to
scroll through the settings, which appear in the following
order:
3.
To change a setting, press the OK button and then use
the
LEFT
and
RIGHT
arrow buttons to adjust as needed.
Press the OK button again to save the changes. See
Figure 4.
NOTE:
The S/N (Serial Number), Elapsed Time, and
Control Temperature can not be adjusted.
4.
When the unit is turned on and ready, you can adjust
the toast quality by pressing the LEFT and RIGHT arrow
buttons on the control panel. After making an adjustment,
test several products to verify they are toasting at the
desired quality.
NOTE:
This setting is maintained when the unit is
powered off. If at any time the unit displays an
error message or if it fails to operate properly,
contact Antunes Technical Service immediately for
service.
Factory Reset
To reset the unit to the factory default settings, press and
hold the
LEFT
and
RIGHT
arrow buttons for 5 seconds until
“Factory Settings Restored” appears on the display.
NOTE:
For ALL Units, this sets the display temperature to
°C (Celsius). Refer to the “Settings” section of this
manual to change the display temperature to °F
(Fahrenheit).
NOTE:
For units with Mfg. No. 9210844, this turns the Club
Platen on. To turn the Club Platen off, refer to the
section titled “Club Platen OFF units with Mfg. No.
9210844” for information.
Adjusting Toast Quality
There are variations in bun products Worldwide that are
used on the HEBT toaster such as moisture content, bun
formulations, age, tolerances etc. The HEBT was designed to
compensate for bun variations by allowing user to adjust the
compression, light/dark (speed) & temperatures settings in
order to achieve a Gold Standard toasted product.
1. LIGHT DARK ADJUSTMENT:
Adjust the light dark setting
with the
LEFT
or
RIGHT
arrow buttons. The default light/
dark setting on the HEBT from the factory is 0 but can be
adjusted from Lighter 0-10 to Darker 0-10. Light 10 is the
lightest setting and dark 10 is the darkest. Each increase
in “lighter” value will decrease the pass through time and
each increase in “darker” value with increase the pass
through time.
2. TEMPERATURE ADJUSTMENT:
Adjust the set point
temperature on the platens in the program menu. The
default temperature settings on the HEBT are A Platen:
271°C (520°F) B Platen: 271°C (520°F) C Platen: 254°C
(490°F). The temperatures can be increased to +/- 50°F
(10°C) if needed to achieve an acceptable toast quality.
•
A Platen
•
B Platen
•
C Platen
•
Units (°C/°F)
•
Buzzer (Soft, Loud,
Mute)
•
Display Languages
•
Serial Number
•
Service Messages
•
ET (Elapsed Time)
•
Controls Temperature
•
Motor
3. COMPRESSION ADJUSTMENT:
Adjust the compression
knob on the left side of the unit. The default compression
setting on the HEBT is 4 but is adjustable from 1-7. It is
acceptable to adjust the compression from 1-7 as needed
to achieve the desired toast quality and bun compression.
4. MOTOR SPEED ADJUSTMENT:
The recommended
Motor setting value is 3300 which equals 22 seconds
(+/- 2 seconds). With the unit plugged in, press and hold
the ‘Menu’ button until the unit displays ‘A Platen’. Press
the
LEFT
arrow button. The display will show ‘Motor’
values. Press the
OK
button and the display will show the
current motor setting. The default value is 4100. Use the
LEFT
arrow to change the motor setting to 3300. Once
the motor is set to 3300, press OK to save the setting.
Run a test bun through the toaster and use a stop watch
to validate that the pass through time is 22 second ±2
seconds. If the bun takes longer than 24 seconds or less
than 20 seconds to pass through the toaster then make
the necessary adjustments to motor setting as described
above to get within range.
Programming
