ANTAIRA LNX-1600-E Series Скачать руководство пользователя страница 18

Страница: 18 / 20

Antaira Technologies - Industrial Ethernet Switches
LNX-1600-E Series - Hardware Manual - v1.0

4.2 Maintenance and Service

●

If the device requires servicing of any kind, the user is required to disconnect and remove it from

its mounting. The initial installation should be done in a way that makes this as convenient as

possible.

●

Voltage / Power lines should be properly insulated as well as other cables. Be careful when

handling them so as to not trip over.

●

Do not under any circumstance insert foreign objects of any kind into the heat dissipation holes

located in the different faces of the device. This may not only harm the internal layout, but might

cause harm to users as well.

●

Do not under any circumstance open the device for any reason. Please contact your dealer for

any repair needed or follow the instructions within the manual.

●

Clean the device with dry soft cloth.

4.3 Troubleshooting

●

Always verify the right power cord or adapter is being used. Never use a power supply or adapter

with a non-compliant DC output voltage or it will burn the equipment.

●

Select the proper UTP or STP cable in order to construct the network. Use an unshielded

twisted-pair (UTP) or shield twisted-pair (STP) cable for RJ45 connections: 100Ω Category 5e for

10/100Mbps. Also be sure that the length of any twisted-pair connection does not exceed 100

meters (328 feet).

●

Diagnosing LED Indicators: To assist in identifying problems, the switch can be easily monitored

with the LED indicators which help to identify if any problems exist.

○

Please refer to the LED Indicators section for LED light indication.

●

If the power indicator LED does not turn on when the power cord is plugged in, the user may have

a problem with the power cord. Check for loose power connections, power losses or surges at the

power outlet.

○

Please contact Antaira for technical support service if the problem still cannot be

resolved.

●

If the industrial switch LED indicators are normal and the connected cables are correct but the

packets still cannot transmit, please check the system’s Ethernet devices’ configuration or status.

Содержание LNX-1600-E Series





















Результаты поиска

Содержание LNX-1600-E Series

Отзывы:

Похожие инструкции для LNX-1600-E Series

Бренды по названию

Популярные бренды

ANTAIRA LNX-1600-E Series, Руководство по оборудованию

Результаты поиска

Содержание LNX-1600-E Series

Отзывы:

Похожие инструкции для LNX-1600-E Series

Бренды по названию

Популярные бренды