ANTAIRA LNP-0501-M-24 Скачать руководство пользователя страница 21

Страница: 21 / 21

Antaira Technologies - Industrial Ethernet Switches

LNP-0501-24 Series User Manual V2.0

Fault Output

1 Relay output

Max Power Consumption

145 Watts (Full load with PoE function)

Installation

DIN-Rail mounting, wall mounting (optional)

Operating Temperature

Standard: -10

C to 70

C (14° to 158° F)

EOT: -40

C to 75

C (-40° to 167° F)

Operating Humidity

5% to 95% (Non-Condensing)

Storage Temperature

-40

C to 85

C (-40°F ~ 185°F)

Case Dimension

IP-30, 46mm (W) x 99mm (D) x 142mm (H)

EMI

FCC Class A

IEC61000-4-2/3/4/5/6/8

IEC61000-6-2

IEC61000-6-4

Stability Testing

IEC60068-2-32 (Free fall)

IEC60068-2-27 (Shock)

IEC60068-2-6 (Vibration)

Safety

UL 508

Table 7.1

LNP-0501-24 Series Technical Specifications

Antaira Customer Service and Support

(Antaira US Headquarter) + 844-268-2472

(Antaira Europe Office) + 48-22-862-88-81

(Antaira Asia Office) + 886-2-2218-9733

Please report any problems to Antaira:

www.antaira.com

[email protected]

www.antaira.eu

[email protected]

www.antaira.com.tw

[email protected]

Any changes to this material will be announced on the Antaira website.

Содержание LNP-0501-M-24






















Результаты поиска

Содержание LNP-0501-M-24

Отзывы:

Похожие инструкции для LNP-0501-M-24

Бренды по названию

Популярные бренды

ANTAIRA LNP-0501-M-24, Руководство пользователя

Результаты поиска

Содержание LNP-0501-M-24

Отзывы:

Похожие инструкции для LNP-0501-M-24

Бренды по названию

Популярные бренды