ANTAIRA LNP-0501-M-24 Скачать руководство пользователя страница 19

Страница: 19 / 21

Antaira Technologies - Industrial Ethernet Switches

LNP-0501-24 Series User Manual V2.0

6. Trouble Shooting



Always verify to have the right power cord or adapter. Never use a power supply or adapter

with a non-compliant DC output voltage or it will burn the equipment.



Select the proper UTP or STP cable in order to construct the network. Use an unshielded

twisted-pair (UTP) or shield twisted-pair (STP) cable for RJ-

45 connections: 100Ω Category

5e for 10M/100Mbps. Also be sure that the length of any twisted-pair connection does not

exceed 100 meters (328 feet).



Diagnosing LED Indicators:

To assist in identifying problems, the switch can be easily

monitored with the LED indicators which help to identity if any problems exist.

Please refer to the LED Indicators section for LED light indication.



If the power indicator LED does not turn on when the power cord is plugged in, the user may

have a problem with the power cord. Check for loose power connections, power losses or

surges at the power outlet.

Please contact Antaira for technical support service, if the problem still cannot

be resolved.



If the industrial switch LED indicators are normal and the connected cables are correct but

the packets still cannot transmit, please check the system’s Ethernet devices’ configuration

or status.

Содержание LNP-0501-M-24






















Результаты поиска

Содержание LNP-0501-M-24

Отзывы:

Похожие инструкции для LNP-0501-M-24

Бренды по названию

Популярные бренды

ANTAIRA LNP-0501-M-24, Руководство пользователя

Результаты поиска

Содержание LNP-0501-M-24

Отзывы:

Похожие инструкции для LNP-0501-M-24

Бренды по названию

Популярные бренды