background image

Antaira Technologies - Industrial Ethernet Switches 

LMP-0601G-SFP-V2 Series Hardware Manual V1.0 

iii 

 

 

 

FCC Warning 

This equipment has been tested and found to comply with the limits for a Class-A digital device, pursuant to Part 

15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a 

residential installation. This equipment generates, uses, and can radiate radio frequency energy. It may cause 

harmful interference to radio communications if the equipment is not installed and used in accordance with the 

instructions. However, there is no guarantee that interference will not occur in a particular installation. If this 

equipment does cause harmful interference to radio or television reception, which can be determined by turning 

the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following 

measures: 

 

Reorient or relocate the receiving antenna. 

 

Increase the separation between the equipment and receiver. 

 

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 

 

Consult the dealer or an experienced radio/TV technician for help. 

 

Caution

: Any changes or modifications not expressly approved by the grantee of this device could void the user's 

authority to operate the equipment. 

 
 
 

CE Mark Warning 

 

This is a Class-A product. In a domestic environment this product may cause radio interference in which case the 

user may be required to take adequate measures. 

 
 

 

Industrial Ethernet Switches 

Industrial Grade Gigabit PoE Managed Ethernet Switches 

 

 

Hardware Manual 

Version 1.0 (October 2019) 

 

 

This manual supports the following models: 

 

LMP-0601G-SFP-V2 

 

LMP-0601G-SFP-T-V2 

 
 
 
 
 
 
 

Содержание LMP-0600 Series




















Отзывы: