ANTAIRA LMP-0600 Series Скачать руководство пользователя страница 16

Страница: 16 / 19

Antaira Technologies - Industrial Ethernet Switches

LMP-0601G-SFP-V2 Series Hardware Manual V1.0

4. Hardware Installation

4.1 Installation Steps

This section will explain how to install

Antaira’s LMP-0601G-SFP-V2 series:

Caution:

This device is intended for use indoor and at altitudes up to 2000 meters.

Caution:

The device is intended to be installed in an industrial control enclosure and panel.

Installation Steps

1. Unpack the industrial Ethernet switch from the original packing box.

2. Check if the DIN-Rail bracket is screwed on the industrial Ethernet switch.

•

If the DIN-Rail is not screwed on the industrial Ethernet switch, please refer to the

DIN-Rail Mounting

section for DIN-Rail installation.

•

If you want to wall mount the industrial Ethernet switch, please refer to the

Wall

Mounting

section for wall mounting installation.

3. To hang the industrial Ethernet switch on a DIN-Rail or wall, please refer to the

Mounting

Installation

section.

4. Power on the industrial Ethernet switch and then the power LED light will turn on.

•

If you need help on how to wire power, please refer to the

Wiring the Power Inputs

section.

•

Please refer to the

LED Indicators

section for LED light indication.

5. Prepare the twisted-pair, straight-through category 5 cable for Ethernet connection.

6. Insert one side of the RJ-45 cable into

switch’s Ethernet port and on the other side into the

networking

device’s Ethernet port, e.g. switch PC or server. The Ethernet port’s (RJ-45) LED

on the industrial Ethernet switch will turn on when the cable is connected to the networking

device.

•

Please refer to the

LED Indicators

section for LED light indication.

7. When all connections are set and the LED lights all show normal, the installation is complete.

Содержание LMP-0600 Series




















Результаты поиска

Содержание LMP-0600 Series

Отзывы:

Похожие инструкции для LMP-0600 Series

Бренды по названию

Популярные бренды

ANTAIRA LMP-0600 Series, Руководство по оборудованию

Результаты поиска

Содержание LMP-0600 Series

Отзывы:

Похожие инструкции для LMP-0600 Series

Бренды по названию

Популярные бренды