
5
General Information
Storing conditions
•
Operating Environment: 14 to 104 deg F (-10 to 40 deg C).
20-85% relative humidity, non-condensing.
Special care instructions !!
•
The camera is designed to be weather resistant. Never
attempt to immerse the unit in water or any other liquid.
This will damage the unit and void the warranty.
•
Use a soft lens cloth for cleaning lens. Avoid touching lens
with fingers. And remove dirt or stains with a soft cloth
dampened with water or neutral detergent. Keep your
camera in a dry and cool dust-free environment or
container when it is NOT used.
•
Take the batteries out, when camera is NOT to be used
over an extended period of time.
•
Avoid dropping your camera on to a hard surface.
•
Do not disassemble your camera.
•
Do not mix new and old batteries.
•
Do not open the camera for unauthorized service. This
could cause serious damage to the unit and WILL void the
warranty.
NOTE : This camera is a precision electronic device. Do
not attempt to service this camera yourself, as opening
or removing covers may expose you to dangerous
voltage points or other risks.
6
Definitions
Definitions of Front View parts
•
Infrared LED :
It is invisible light for night time capture.
•
Strap Holes :
It is to attach the camera to pillar or tree by
provided strap.
•
Microphone :
It is to pick up the sounds while video in
recording.
•
Test Laser Beam :
It is to identify the capture area when
camera switched to SET and holds the
[M]
button with 3
seconds.
Please avoid the laser beam point to your eyes.
•
Status display :
It is to display the setting and camera
status.
•
Camera Lens :
It is to capture the image/video.
•
[
▲
]Up and [
▼
]
Down Button :
Pressing to change the
mode and adjust the setting value when camera switched
to SET.
•
Confirm Button :
Pressing to confirm the settings.
•
[M] Menu Button :
Pressing into the menu to change the
setting.
•
Python Cable Holes :
It is to lock the camera to pillar or
tree by Python cable (Sold Separately).
•
Passive Infrared Sensor :
It is to detect the moving object.
7
•
Locker :
It is to lock the cover in right location.
•
Cover :
It is a cover to prevent the water leakage, close
up with locking after settings.
Definitions of Back View parts
•
Power Port Cover :
Open it to connect a DC 12V external
power or battery pack (Sold Separately) in right polarity.
Tightly close to prevent the water leakage.
•
Lock Hole :
Attaching a locker to prevent unauthorized
changing of settings or SD card stealing.
•
AV Out Port :
It is to connect the camera to TV by AV
cable (Sold Separately) to play the captured image/video.
•
USB port :
It is to connect the camera to PC by provided
USB cable for captured image/video download.
•
External Power Port :
It is to connect a 12V DC external
power or battery pack (Sold Separately).
•
Switch :
It is camera mode switch, switching to change
camera into SET or power OFF or Preset A, B or MANUAL.
•
SD Card Slot :
It is to install the SD memory card, camera
supported SD memory card up to 32GB.
•
Battery Tray :
It is a container to install 8 pieces AA
alkaline batteries.
•
Battery Tray Releaser :
Pressing to release the battery tray,
and then pull it out to install or replace the batteries.
NOTE : Make sure the installed batteries or the external
power is in correct polarity.
8
Definitions of Status Display
•
CAM
:
It indicates the camera in still image mode.
•
VIDEO
:
It indicates the camera in vide mode.
•
:
It indicates the number of burst capture.
•
:
It indicates the battery status.
> <
> <
> <
Full (Icon on) Half (Icon blinking) Low (Icon off)
When batteries are low, the status display will showing
“bAtLO”. Please replace with new batteries.