ANK L4 EL34i Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 73

background image

Copyright © 2018 AudioNote Kits

www.AudioNoteKits.com

[email protected]

Page 57

Twist one end of the 7" and 9" Black wires together, tin them, and solder them to a Black
speaker post. Do the same for the other Black speaker post.

Now prepare the following Red wires:

4 Red wires of approximately 7". These MUST be long enough to reach from the middle and

upper Red speaker posts to the Blue and Purple lugs on the Output Transformers.

2 Red wires of approximately 9". These MUST be long enough to reach from the upper Red

speaker posts to the solder pads marked '8R' on the ECF80/EL34 PCB.

Now make the following connections:

Solder two 7" lengths of Red wire to the two middle Red speaker posts, one for each side.

Twist one end of the one of the remaining 7" and a 9" Red wire together, tin them, and solder

them to the one of the upper Red speaker posts. Do the same for the other upper Red
speaker post.

«
...
55
56
57
58
59
...
»

Содержание L4 EL34i










































































Отзывы:

Нет отзывов

Похожие инструкции для L4 EL34i

Бренд: NAD Страницы: 2

Бренд: Jensen Страницы: 12

Бренд: Jedia Страницы: 16

Бренд: Cable-Tronix Страницы: 5

Бренд: Yaesu Страницы: 132

Бренд: Tokyo Страницы: 11

Бренд: ifi Страницы: 35

Бренд: Teac Страницы: 28

Бренд: Engl Страницы: 8

Бренд: Line Magnetic Страницы: 16

Бренд: Sundown Audio Страницы: 8

Бренд: CAKEWALK Страницы: 68

Бренд: Amperes Страницы: 8

Бренд: AR Страницы: 58

Бренд: INVADERS Amplification Страницы: 6

Бренд: Velleman-Kit Страницы: 16

Бренд: Fagor Страницы: 2

Бренд: ValveTrain Amplification Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды