Anita GP-510- 446(7) Скачать руководство пользователя страница 4

Страница: 4 / 68

anita-b

GP-510-446(7)

2 Putting the machine into operation

Following instructions must be observed to avoid risk of failures or damage to the

machine:

- clean the machine of preserving agents

- drop 1-2 drops of oil into looper

- remove the front cover and oil the ends of needle bar connecting-rod and of the cross-head

slide of thread take-up.

- a specialist shall check if the electrical equipment is in good order incl. necessary voltage

for motor and see to it that machine hand wheel rotates towards the operator (see arrow)

when the electric motor is connected.

-do not run the machine at full speed during the first two weeks, sewing should be performed

at ca. 3/4 of the maximum speed.

Caution!

Do not interfere with the electric equipment of the machine, call an electrician. Danger of

electrical accident. When working on the machine or close to the machine take care that

you do not give cause to an accident. See to it that no liquid can get into the electrical

equipment and cause a short-circuit or any other failure of the electrical equipment.

Observe the generally valid safety regulations.

When running the machine, be very cautious especially near the needle, trimming knives,

thread take-up and cloth pressing elements.

When the machine head is tilted on its support, take special care so that the whole machine

and support may not tilt over.

To tilt the machine into working position take the head with both hands to avoid any injury

between the tilted machine and the base plate.

Содержание GP-510- 446(7)





































































Результаты поиска

Содержание GP-510- 446(7)

Отзывы:

Похожие инструкции для GP-510- 446(7)

Бренды по названию

Популярные бренды

Anita GP-510- 446(7), Руководство пользователя

Результаты поиска

Содержание GP-510- 446(7)

Отзывы:

Похожие инструкции для GP-510- 446(7)

Бренды по названию

Популярные бренды