Angel Armor Avail III Скачать руководство пользователя страница 4

Installation Guide

      

  

Angel Armor Avail ballistic door panels (Level III) FOR DODGE CHARGER PURSUIT

970 235 2961            [email protected]om               angelarmor.com

4

Warnings and Cautions 

Please adhere to the following 
guidelines to prevent personal 
injury, equipment damage and 
unnecessary difficulty during 
installation. 

DISCONNECT THE VEHICLE BATTERY AFTER 
THE WINDOW IS ADJUSTED FOR REMOVAL/
INSTALLATION TO AVOID ACCIDENTAL 
AIRBAG DEPLOYMENT. ACCIDENTAL 
DEPLOYMENT OF THE AIRBAG MAY CAUSE 
SERIOUS PERSONAL INJURY.

  Read this guide in its entirety before 

beginning installation. 

  Wear appropriate protective gear, including 

eye, hand and foot protection. 

  Use extreme caution when transporting the 

ballistic door panel. The armor panel is very 
heavy and impact may result in serious injury.

  To avoid muscle strain or back injury, use 

lifting aids and proper lifting techniques 
when transporting the ballistic door panel.

  Avoid excessive force when inserting the 

armor into the car door. Excessive force may 
damage the weatherstripping or scratch 
finished surfaces.

  Avoid puncturing speakers with screws, 

push-snaps, fasteners or other sharp pieces 
during door disassembly, panel insertion and 
door re-assembly.

Legal Statements 

See Warranty and Terms and Conditions 
for important legal information on 
angelarmor.com. These instructions are 
provided for your convenience only, 
and Angel Armor expressly disclaims 
any liability for any damage to personal 
property or personal injury that occurs as 
a result of either installation or removal 
of panels.

  Do not drop screws or other assembly 

components inside the door, as they may be 
difficult to retrieve. If possible, use magnetic 
tools during installation. 

  Use only plastic trim removal/prying tools on 

finished surfaces to help prevent scratching.

  Discard and replace any door components 

that are inadvertently damaged during 
the installation process. Proper installation 
according to the instructions in this guide 
should not cause damage to any vehicle or 
window armor parts or components.

  Use caution when removing parts that may 

have sharp edges, such as the outer window 
weatherstrip.

Содержание Avail III























Отзывы: