background image

3

INSTALLATION 

PREPARATION

2

b

a

1. 

Most homeowners prefer to have the storm door 

handle on the same side as the entry door handle.  

In shallow door openings, this can cause the two 

handles to interfere 

(see Figure 4)

.

2. 

Check for potential interference by measuring up 

from the Door Sill 40 1/2". Measure in from 

mounting 

surface

 on 

brickmould

 3 1/8". This is roughly the 

location and depth of the storm door handle.

3. 

If you anticipate interference, purchase a storm door 

hinged on the opposite side of your entry door.

In this step, you will confirm that your storm door hinges on the correct side.

1. 

To determine the exterior and interior of the door panel: at the bottom of the door,  

the interior side has a sweep with screws 

(Figure 5)

.  The exterior is the side without  

a sweep and screws.

2. 

Left Handed 

(Figure 6)

: From the exterior, a left handed storm door will have the handle 

holes on the left side of the storm door. 

See pages 4-8

 for installation instructions.

3. 

Right Handed 

(Figure 7)

: From the exterior, a right handed storm door will have the handle 

holes on the right side of the storm door. 

See pages 9-13

 for installation instructions.

Figure 6

Figure 7

40 1/2"

GRASP 

HERE

c

d

1. 

Remove door from carton, grasping it as shown. 

Support door’s weight by the door frame, not by 

hinge and latch rails.

2. 

Set aside rain cap extender and the screw covers 

for use in a later step

Ensure all clips are properly attached.

1. 

With door standing from the exterior, ensure 

latch rail is properly seated in orange spacer clips 

(I), and ensure bottom spacer (J) is attached to 

bottom of door and slid to handle side.

NOTE: See troubleshooting section at end of install 

guide if bottom spacer becomes detached.

LEFT HAND

Proceed to  

Page 4-8

RIGHT HAND

Proceed to  

Page 9-13

 Figure 5

i

VIEW

i

VIEW

X

VIEW

X

VIEW

TO DOOR SILL

X

VIEW

J

I

Tape Measure

 

MOUNTING  

SURFACE

BRICKMOULD

(EXTERIOR

TRIM)

DOOR

FRAME

HINGE

RAIL

LATCH

RAIL

MIN. 

3 1/8"

 Figure 4

Tools needed:

Bottom Spacer

Spacer Clips

J

I

=

=

X

VIEW

i

VIEW

 

EXTERIOR  

VIEW

 

INTERIOR  

VIEW

Содержание 901724















Отзывы: