AnaLynk A753 Скачать руководство пользователя страница 2

Installation and Operation Manual for  

4-20mA RF Wireless Transmitter Model A753 

Analynk Wireless, LLC 

!

 790 Cross Pointe Road 

!

 Columbus, OH 43230 

Phone: (614) 755-5091 Fax: (614) 755-5093 Web: 

www.analynk.com

 

• 

The Model A753 offers simplicity and 
reliability in a point to point RF system.   

• 

Designed for easy transmission of 4-
20mA or other DC signals.  

• 

Two discrete (switch) inputs, switch in-
puts can be wet or dry.   

• 

Two radio power levels available: 1W 
or 50mW (A753-LP). 

• 

11 to 32 Vdc power (nominal 24 Vdc). 

• 

Repeaters can be added to extend 
range with no programming.   

• 

Simple dip switch selectable RF chan-
nel. 

• 

No software required. 

• 

RSSI test (received signal strength in-
dicator test). 

• 

Convenient 35 mm DIN rail installation. 

• 

Designed to interface with A750 re-
ceiver. 

• 

Demo mode. 

1.0 Features 

2.0 Description 

The A753 has one 4-20mA input and two discrete inputs. Other analog inputs are 
available always refer the label on the side of the unit to determine proper input. Dis-
crete inputs can be either wet or dry. The status of the discrete inputs is displayed on 
the front panel as A1 and A2.  The 4-20mA input signal is replicated on the receiver’s 
4-20mA output.  Similarly the state of switches A1 and A2 are mapped to the receiver’s 
A1 and A2 respectively. To facilitate installation, the transmitter is designed for 35mm 
DIN mount and powered by the industry st24Vdc (11 to 32 Vdc).  The receiver 
model A750 is sold separately. The Model 753 can be used with a repeater (Model 
A759).  If a repeater is used – please refer to section 4.4 for configuration. 

Transmitter 

A753 

Receiver 

A750 

(sold separately) 

Содержание A753









Отзывы: