Analog Devices AD9910 Скачать руководство пользователя страница 14

Страница: 14 / 17

UG-207

Evaluation Board User Guide

Rev. A | Page 14 of 16

RAM OPERATION

Figure 13. Profiles Window When Using the RAM

Use of RAM on the AD9910 should not be attempted without
using the AD9910 data sheet as a reference. The AD9910 data
sheet contains detailed information on RAM operation. To use
the RAM on the AD9910, select the

Enable RAM

check box

on the

Profiles

window. This changes the appearance of the

window from single-tone mode to RAM control mode.

Each

RAM Segment

section corresponds to a different profile.

RAM Segment 0

corresponds to

Profile 0.

Use the

Beginning

Address

and

Final Address

text boxes to set the beginning and

ending addresses for the RAM sweep. The

Address Step Rate

sets the 16-bit address step rate value. The

Mode Control

drop-

down box sets the 3-bit RAM control word mode. See the
AD9910 data sheet for a complete description of the RAM
operating modes. The

Zero Crossing

check box sets the zero-

crossing bit. This bit is effective only in RAM mode using direct
switch. The

No Dwell

check box

sets the no-dwell high bit. This

bit is only effective when the RAM mode is in ramp-up.

Use the

Activate

area to switch between profiles. Use the

Internal Profile Control

drop-down box to select the internal

profile control configurations. Refer to the AD9910 data sheet
for detailed information on the RAM internal profile control
modes. Use the

RAM Data Type

drop-down box to select the

RAM playback destination. Refer to the AD9910 data sheet for
further details on the RAM playback destination bits.

Use the

LOAD

button to display the

RAM I/O

window.

RAM I/O

Figure 14. RAM I/O Window

Содержание AD9910


















Результаты поиска

Содержание AD9910

Отзывы:

Похожие инструкции для AD9910

Бренды по названию

Популярные бренды

Analog Devices AD9910, Руководство пользователя

Результаты поиска

Содержание AD9910

Отзывы:

Похожие инструкции для AD9910

Бренды по названию

Популярные бренды