background image

Evaluation Board User Guide

UG-559

One

 

Technology

 

Way

 

 

P.O.

 

Box

 

9106

 

 

Norwood,

 

MA

 

02062-9106,

 

U.S.A.

 

 

Tel:

 

781.329.4700

 

 

Fax:

 

781.461.3113

 

 

www.analog.com 

Evaluating the 

AD8338

 Low Power VGA 

PLEASE SEE THE LAST PAGE FOR AN IMPORTANT  
WARNING AND LEGAL TERMS AND CONDITIONS.

 

Rev. B | Page 1 of 8 

FEATURES 

Full featured evaluation board for the 

AD8338

 

On-board voltage regulator 
On-board potentiometers for direct adjustment, with test 

points for electronic adjustment 

All analog design, no software needed 

EVALUATION KIT CONTENTS 

AD8338-EVALZ 

evaluation board 

AD8338-EVALZ

 user guide (

UG-559

ADDITIONAL EQUIPMENT NEEDED 

A signal generator 
A power supply capable of 6 V to 20 V output 
An oscilloscope with a 100 MHz minimum bandwidth 
3 SMA (M) to BNC (M) cables 

ONLINE RESOURCES 

AD8338

 data sheet 

UG-559

 user guide 

GENERAL DESCRIPTION 

This user guide describes the 

AD8338

 evaluation board and 

discusses common configurations. The design of this board 
(

AD8338-EVALZ

) emphasizes simplicity and ease of use,  

which is evident in the minimalist approach to connector 
implementation.  

The 

AD8338

 data sheet, available at 

www.analog.com

, covers 

the details for the operation of the 

AD8338

. The 

AD8338 

data 

sheet should be consulted in conjunction with

 

this user guide. 

The data sheet not only assists designers in their end 
applications but also provides important information to 
understand the operation of the 

AD8338

 evaluation board, 

especially its initial configuration and power up.  

AD8338-EVALZ

 EVALUATION BOARD 

Figure 1.  

1

15

10-

00

1

Downloaded from

Arrow.com.

Содержание AD8338-EVALZ









Отзывы: