background image

 

16 

 

Repeat the cycle “opening-closing”. Make sure  that the doors move in the required direc-
tion,  door  curtain  must  move  evenly  without any  changes  of  speed.  The  movement  must 
slow down at approximately 200mm height from the final position. 

 

Make  sure that the illuminating lamp is “lit” when the drive works and “goes out” after 3 
minutes after final shut-off.  

 

Check the photo cells (if there are any), they must not be connected with other devices. To 

do  it  block  the  optic  axis  using  a 

cylindrical  bar 

(diameter  50mm,  length  300mm):  firstly 

close to TX-photo cell (transmitter), then close from RX- photo cell (receiver) and at last in 
the middle between two photo cells. Make sure that in all cases the drive functions correctly 
during the functioning of photo cells (while closing the drive stops and the illumination lamp 
blinks several times, then the drive opens the doors). 

 

Check the ability of the set to find the interconnection with alien objects in the process of 
opening.  While  opening  load  the  doors  in  the  middle  of  the  bottom  edge  with  20kg  (not 
more). The doors must stop. 

 

Check the ability of the set to find the interconnection with alien objects in the process of 
closing (monthly test). Put on the floor an obstacle 40mm high. Close the doors. When the 
doors touch the obstacle the drive must stop them and open fully. If it is necessary adjust 
the effort (section «Adjustment»). 

7.2.  Commissioning 

Commissioning of the drive system must be held only after successful testing. Partial commis-
sioning or temporary operation is not acceptable. 
To perform the commissioning follow the instructions: 

 

Prepare and keep the technical documentation for the set of automation. The documenta-
tion  must  contain:  general  drawing,  electric  scheme,  installation  and  operation  manual, 
schedule of service maintenance. 

 

Adjust near the doors the permanent label or  sign with the description of unblocking and 
manual opening of the doors. 

 

Adjust  near  the  doors 

at  a  visible  place  the

  permanent  safety  label  containing  the  following 

text: “Attention! Automatic drive. Don’t stay near the doors as it can unexpectedly be acti-
vated. Don’t allow children to stay near the doors during their movement”. 

 

Adjust 

at  a  visible  place

 near the doors or stationary control devices the warning label with 

the following text: “Attention! Risk of jamming — Regularly check and if required adjust the 
device, if the doors touch an object 40mm high positioned on the floor the direction of their 
movement must change to the opposite or there should be a possibility to release the ob-
ject from under the doors ”. 

 

Give the completed «Installation and operation manual» to the customer. 

 

Prepare «Schedule of service maintenance» and give it to the customer. 

 

Before commissioning inform the customer about risks and about rules of safe operation. 

 

8.  OPERATING 

While operating: 

 

Don’t allow children to play with control elements. Control panels must be positioned out of 
children’s reach. 

 

Don’t ever hold the moving parts of the doors. 

 

Before operate the doors make sure that in a dangerous area there are no people, animals, 
transport or any objects. Observe the process of door movement. It is forbidden for people 
and transport to pass under the doors when they are moving. 

 

Be careful while using the manual unblocking device because the door can suddenly fall due 
to loosening or break of the spring or balancing system. 

 

People operating the doors or their representatives after the commission of the automation 
set must be instructed concerning its service maintenance. 

 

Check the safety devices functioning monthly. 

 

Examine  the  drive  system  regularly  in  particular  check  cable,  springs,  and  mounting 
reinforcement on their level of ware, damage or unbalance. It is forbidden to use the doors 
wanted repair or regulation because the installation defect or incorrect balancing can lead 
to injuries or drive damage. 

Содержание ASG1000/3KIT
























Отзывы: