AMX NetLinx NXI Скачать руководство пользователя страница 18

Страница: 18 / 26

Programming

NetLinx Integrated Controller (No Master) - Operation Reference Guide

RS-232/422/485 Send_Commands (Cont.)

SET BAUD

Sets the RS-232/422/485 port's communication parameters.

Syntax:

SEND_COMMAND <DEV>,'SET BAUD (Baud),(Parity),(Data),(Stop)

(485 DISABLE/ENABLE)'

Variables:

Baud = 150, 300, 600, 1200, 2400, 4800, 9600, 19200, 38400 (factory set default), 57600, 76800,
115200, 230400

Parity = N (none), O (odd), E (even), M (mark), S (space)

Data = 7 or 8 data bits

Stop = 1 or 2 stop bits

485 Disable = Disables RS-485 mode and enables RS-422.

485 Enable = Enables RS-485 mode and disables RS-422.

Example:

SEND_COMMAND RS232_1,'SET BAUD 9600,N,8,1 485 ENABLE'

Sets the RS232_1 port's communication parameters to 9,600 baud, no parity, 8 data bits, 1 stop bit, and
enables RS-485 mode.

TSET BAUD

Temporarily sets the RS-232/422/485 port's communication parameters.

TSET BAUD works the same as SET BAUD, except that the changes are not permanent, and the
previous values will be restored if the power is cycled on the device.

Syntax:

SEND_COMMAND <DEV>,'TSET BAUD (Baud),(Parity),(Data), (Stop)

(485 DISABLE/ENABLE)'

HSOFF

Disables hardware handshaking (default).

Syntax:

SEND_COMMAND <DEV>,'HSOFF'

Example:

SEND_COMMAND RS232_1,'HSOFF'

Disables hardware handshaking on the RS232_1 device.

HSON

Enables RTS (ready-to-send) and CTS (clear-to-send) hardware handshaking.

Syntax:

SEND_COMMAND <DEV>,'HSON'

Example:

SEND_COMMAND RS232_1,'HSON'

Enables hardware handshaking on the RS232_1 device.

RXCLR

Clears all characters in the receive buffer waiting to be sent to the Master Card.

Syntax:

SEND_COMMAND <DEV>,'RXCLR'

Example:

SEND_COMMAND RS232_1,'RXCLR'

Clears all characters in the RS232_1 device's receive buffer waiting to be sent to the Master Card.

RXOFF

Stops transmitting received characters to the Master Card (default).

Syntax:

SEND_COMMAND <DEV>,'RXOFF'

Example:

SEND_COMMAND RS232_1,'RXOFF'

Stops the RS232_1 device from transmitting received characters to the Master Card.

RXON

Starts transmitting received characters to the Master Card.

This command is sent automatically when issuing a CREATE_BUFFER SEND_COMMAND.

Syntax:

SEND_COMMAND <DEV>,'RXON'

Example:

SEND_COMMAND RS232_1,'RXON'

Sets the RS232_1 device to transmit received characters to the Master Card.

Содержание NetLinx NXI



























Результаты поиска

Содержание NetLinx NXI

Отзывы:

Похожие инструкции для NetLinx NXI

Бренды по названию

Популярные бренды

AMX NetLinx NXI, Руководство по эксплуатации/справочник

Результаты поиска

Содержание NetLinx NXI

Отзывы:

Похожие инструкции для NetLinx NXI

Бренды по названию

Популярные бренды