For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).
065-004-2971 6/06
©2006 AMX. All rights reserved. AMX and the AMX logo are registered trademarks of AMX.
AMX reserves the right to alter specifications without notice at any time.
3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com
93-2178-16
REV: C
Step 4: Mount the Adapter Bars to the Rack-Rail assemblies
1.
Use the included mounting hardware to attach an Adapter Bar to the front and
rear of each of the two Rack-Rail assemblies:
To ensure a proper fit, make sure that each Adapter Bar is mounted flush
against all sides of the tabs on the Rack-Rail assembly. When the Adapter Bar
is seated properly against the tabs on the front of the Rack-Rails, the bottom of
the Adapter Bar should be flush with the bottom of the Rack-Rail (FIG. 5).
2.
Attach an Adapter Bar to the rear of each of the two Rack-Rail assemblies
(FIG. 6). Once the Adapter Bars have been attached to the front and rear of
both Rack-Rail assemblies, the Rack-Rails are ready to use.
Step 5: Mount the Rail/Bracket Assemblies Into the
Equipment Rack
Once the Extension Brackets (or End Brackets) and Adapter Bars have been
attached to the Rail Assemblies, the Rail/Bracket Assemblies are ready to be
mounted into the equipment rack.
Install the Rack-Rail assemblies into the equipment rack, aligning the holes on the
Adapter Bars to the mounting rails in the rack as shown in FIG. 7.
FIG. 8 shows the Adapter Bars properly mounted to the Rack-Rail assemblies and
vertical mounting rails in the equipment rack. Note that the notched edge of the bar
is placed in the corner of the mounting rails in the equipment rack. This notched edge
accomdates any flange that may exist on the inside corner of the mounting rails:
Step 6: Load the HT Server Into the Rack
Once the Rail Assemblies have been installed into the equipment rack cabinet, the
server can be mounted on the rails and slid into the rack (FIG. 9):
1.
Slide the Rails (Intermediate Sections) out to their fully extended position.
2.
Carefully align the Chassis Sections (mounted on the HT server) with the
extended Rails.
3.
Slide the server onto the extended rails.
Keep the server parallel to the floor
when sliding the server rails into the rails. Tilting the server up or down could
result in damage to the Slide Rails.
4.
Carefully slide the server into the rack until the Locking Release Tabs on the
Chassis Sections (in the equipment rack) engage the Intermediate Section
Rails, securing the server in place.
FIG. 4
Attach the Extension Brackets to the Stationary/Intermediate Sections
FIG. 5
Adapter Bar mounted to the front of the Rack-Rail assembly
FIG. 6
Mount the Adapter Bars to the Rail assemblies
Mounting tabs (rear)
Secure to the rear rails on the equipment rack
Mounting tabs
Secure to the front rails on
the equipment rack
Extension Bracket
Stationary Section/Intermediate
(front)
(rear)
Section Rail Assembly
(on the front of the rail assembly
FRONT VIEW
REAR VIEW
Use the
outside
and
center
holes to
The bottom of the Adapter Bar sits flush against the tabs on the Rack-Rail assembly
mount the Rack-Rail w/ Adapter Bars to
the equipment rack
Use these holes to mount the Adapter
Bar to the Rack-Rails
Adapter Bar
Mounting rails on equipment rack
Rail Assembly
Adapter Bar
(rear)
(front)
Notched edge of the Adapter Bar
goes against the inside corner
of the mounting rails
(see FIG 8)
FIG. 7
Align the holes on the Adapter Bar to the holes on the rails in the equipment rack
FIG. 8
Adapter Bars mounted to the equipment rack
FIG. 9
Sliding the server chassis into the rack
Adapter Bar
Mounting Rail in equipment rack
Align the center hole on the Adapter Bar to a center hole
Align the top hole on the Adapter Bar to the bottom hole
Align the bottom hole on the Adapter Bar to the top hole
of the upper-adjacent RU in the equipment rack.
in one of the RUs in the equipment rack.
of the lower-adjacent RU in the equipment rack.
Front mounting rail on the
Rear mounting rail on the
equipment rack
equipment rack
The notched edge of the Adapater Bar should be
placed against the inside corner of the mounting
rails inside the equipment rack.
Chassis Section
Intermediate Section
(fully extended)
CAUTION!
Refer to the Safety Instructions
on page one before installing
the server chassis into the
equipment rack
Equipment Rack
