The Crestron® TS-5-MSMK multisurface mount kit provides a versatile mounting solution for
Crestron TSW-560, TSW-560P, and TSW-560-NC touch screens. Using the TS-5-MSMK, the
touch screen may be mounted directly onto glass, granite, marble, plaster, smooth stone and
masonry, or almost any other flat surface using the included adhesive mounting plate.
The TS-5-MSMK comes with two rear housings—one with a cutout hole in the top of the housing
and one with a cutout hole in the side of the housing—for running concealed cables to the touch
screen using the included adhesive-backed raceway. Depending on the desired cable route, the
appropriate rear housing can be used in the installation to eliminate unused cutout holes.
Check the Box
Item
Qty
TS-5-MSMK
1
Coupler, Plastic (P/N 2049574)
2
Fitting, Plastic, Inside Corner (P/N 2049571)
1
Fitting, Plastic, Outside Corner (P/N 2049572)
1
Fitting, Plastic, Right Angle (P/N 2049573)
2
Raceway, PVC, 3 ft x 0.45 in. x 0.77 in. (P/N 2049567)
3
Screw, 4-40 x 1/4 in., Undercut Head, Phillips, Black (P/N 2007152)
2
Screw, 4-40 x 3/8 in., Undercut Head, Phillips, Black (P/N 2007173)
2
Spacer, Nylon, with Adhesive (P/N 2053356)
2
Template, Overlay (P/N 4529901)
1
TS-5-MSMK-B Only
Bracket, Plastic, Side Cutout, Black (P/N 4529685)
1
Bracket, Plastic, Top Cutout, Black (P/N 4529683)
1
Cap, Plastic, with Adhesive, Black (P/N 4529686)
1
Mounting Plate, with Adhesive, Black (P/N 4529681)
1
TS-5-MSMK-W Only
Bracket, Plastic, Side Cutout, White (P/N 4529684)
1
Bracket, Plastic, Top Cutout, White (P/N 4529682)
1
Cap, Plastic, with Adhesive, White (P/N 4529579)
1
Mounting Plate, with Adhesive, White (P/N 4529680)
1
Install the TS-5-MSMK
Use the following procedures to mount the TS-5-MSMK onto a flat pane of glass or a similar
smooth surface (such as granite, marble, plaster, or smooth stone and masonry). The adhesive
on the TS-5-MSMK mounting plate attaches permanently to the surface.
NOTE:
For portrait touch screens (such as the TSW-560P), the TS-5-MSMK may be installed
vertically using the same procedures required for a landscape touch screen installation.
After the installation is complete, the included raceway kit may be installed on a nearby smooth
surface to conceal cables running to the touch screen. For more information, refer to the “Install
the Raceway Kit” section.
The following supplies (not included) are required for this installation: a level, a roll of tape, a
Phillips screwdriver, and a surface cleaning product that does not leave a film.
Attach the Mounting Plate to the Surface
1.
Clean and dry the mounting surface thoroughly.
2.
Use a level to tape a horizontal reference line to the surface to align with the lower edge of
the mounting plate.
3.
Remove the protective covering from the rear of the TS-5-MSMK mounting plate.
CAUTION:
The adhesive on the rear of the mounting plate is high-strength bond. Once the
adhesive comes in contact with a surface, it cannot be removed easily.
4.
Hold the mounting plate at a 45-degree angle to the surface, and then carefully align the
lower edge of the pad with the taped reference line. Do not allow the adhesive to come in
contact with the surface.
5.
Attach the mounting plate to the surface, starting with the bottom edge near the taped
reference line. Press the pad to the surface firmly to ensure proper adhesion and to
eliminate any trapped air bubbles.
Mounting plate
Glass surface
Select a Rear Housing for the Installation
The TS-5-MSMK ships with two rear housings: one with a cutout hole in the top of the housing
and one with a cutout hole in the side of the housing. Use the rear housing that supports the
desired cable route. The unused rear housing may be discarded or retained for future use.
Rear housing
(with top cutout)
Rear housing
(with side cutout)
To determine the correct rear housing to use for the installation:
1.
Decide where the included raceway will be installed and whether the raceway will be
entering the rear housing from the top, bottom, left, or right side.
2.
Select the apporpriate rear housing:
•
Select the rear housing with the side cutout if the raceway will enter the housing from
the left or right sides.
•
Select the rear housing with top cutout if the raceway will enter the housing from the
top or bottom.
3.
Rotate the rear housing until the cutout is positioned next to the raceway opening.
Attach the Rear Housing to the Mounting Plate
NOTE:
If the TSW-560-LB light bar will be installed with the touch screen, refer to the
TSW-560-LB Quick Start (Doc. 8367) at
www.crestron.com/manuals
for instructions. The
included 4-40 x 1/4 in. screws and nylon spacers are required for this installation.
1.
Loosely route any necessary cables through the cutout hole in the chosen rear housing and
out of the center opening of the rear housing.
2.
Remove the protective strips from the rear of the TS-5-MSMK rear housing.
3.
Hold the rear housing at a 45-degree angle to the surface, and then carefully align the
lower edge of the rear housing with the mounting plate. Do not allow the adhesive to come
in contact with the surface.
4.
Attach the rear housing to the surface, starting with the bottom edge near the mounting
plate. Press the rear housing to the surface firmly to ensure proper adhesion and to
eliminate any trapped air bubbles.
Mounting plate
Raceway
Glass surface
Rear housing
(with side cutout)
NOTE:
The raceway shown in the image above conceals cables running to the touch screen
and can be installed to the surface before or after the rear housing is installed. For more
information, refer to the “Install the Raceway Kit” section.
Attach the TSW-560 Mounting Bracket to the TS-5-MSMK
1.
Separate the two halves of the TSW-560 mounting bracket (included with the touch
screen) by removing the two 1-1/2 in. screws that hold the halves together. These screws
may be discarded.
NOTE:
The rear half of the TSW-560 mounting bracket is not used in this installation and
may be retained for future use or discarded.
2.
Use the included 4-40 x 3/8 in. screws to attach the front half of the TSW-560 mounting
bracket to the mounting plate through the center opening of the rear housing. The screws
attach to the two raised screw holes in the mounting plate.
Rear housing
(side cutout)
TSW-560
mounting bracket
(front half)
Screw (2):
4-40 x 3/8 in.
Mounting plate
TS-5-MSMK
Multisurface Mount Kit for TSW-560, TSW-560P, and TSW-560-NC
