manualshive.com logo in svg

AMX AXD-EL Plus, Инструкция по эксплуатации

Поделиться
Скачать
AMX AXD-EL Plus Скачать руководство пользователя страница 44

Upgrading the Firmware

40

Electroluminescent LCD Touch Panels

9.

Insert all the prongs simultaneously until each is firmly resting in its socket hole and the entire 

chip is securely connected to its base. 

10.

Rotate the circuit card back to the original position and place it in the touch panel housing. 

11.

Plug the 2-pin power or AXlink connector back into the touch panel for approximately 

1 minute. Once you can confirm the panel is receiving power, remove the connector, align the 

screw hole and insert the Phillips-head screw and tighten.

12.

Replace the bottom panel and align the screw holes. Insert the seven Phillips-head screws and 

tighten.

13.

Plug all connectors back into the touch panel.

AXM-EL+ (/PB) and AXD-EL+ (/PB) EPROM Replacement

If the unit is already mounted to a surface, remove it at this time. Refer to the

Installation

section on 

page 3 for more information.

1.

Discharge the static electricity from your body by touching a grounded object.

2.

Remove the 2-pin power connector from the rear side of the panel. If you are using power via 

AXlink, remove the AXlink connector.

3.

Flip the touch panel face down onto a soft cloth, and remove the seven Phillips-head screws 

from the bottom panel. Then, gently remove the housing.

4.

Remove the Phillips-head screw located in the center of the circuit card.

5.

Gently tilt the circuit card down towards the connector side and pull backwards until you clear 

the connector housing. Then, slowly rotate the circuit card backwards until you can lay it down 

flat with the EPROMs exposed as seen in FIG. 17. EPROMS have stickers that indicating the 

firmware version.

6.

Carefully remove each EPROM by inserting a Phillips screwdriver with a non-conducting flat-

blade between the EPROM and the connection site (at the notch side).

7.

Gently pry the EPROMs from their connection base until they begin to loosen. Carefully pull 

them out by either using an EPROM removal device or by gently pulling them from their base 

(making sure to evenly pull the prongs from their socket holes).

FIG. 17  

EPROM location on a mounted touch panel

 

1 1

JP2JP1JP3

1

ODD

32-pin sockets
EPROM Odd
and Even

EVEN

Содержание AXD-EL Plus



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды