background image

American Security Products Co.  

ESL20XL Operating Instructions 

Released Aug. 9, 2018 

Revision A

 

Page 5 of 10 

 

Combination Changes in Multi-User Mode 

One of the strengths of an electronic safe lock is the quick and easy changing of the combination(s). This adds to security 

because you can change it at will if you suspect your combination is known by others. 
The combination change method for the primary User (Master User) can be done two ways, with or without a User 

Number. All combination changes require and authorization code and two entries of the new combo. 

o

 

In the event that F60 (Subordinate Combo Change) is set to Disable (F60=0), only the Master Code can 

authorize a code change for a Subordinate User. 

o

 

Each Subordinate User is assigned a single digit “User Number” (1 thru 8) during enrollment by the 

Master User. Master User is User 0. Armored Car User is User 9. 

 

Master User Code change

 - At any time, the Master User combo can be changed by keying:  

C - # - (Old Master Code) - # - (New Master Code) - # - (New Master Code) - # 

 

User Code Change and F60=1

 - Changing of any combination, including the Master User Code, can be 

changed by the following sequence: 

C- # - (User No.) - # - (Old User Code) - # - (New User Code) - # - (New User Code) - # 

 

User Code Change and F60=0

 - In the event F60 is Disabled (F60=0) or you are adding a new User, then the 

combo change must be authorized with the Master User’s code: 

C- # - (User No.) - # - (

Master Code

) - # - (New User Code) - # - (New User Code) - # 

 

Feature Setting with Function Codes. 

The ESL20XL’s advanced features are controlled 

only 

by the Master User, and are set using Function Codes. 

A function can be turned on and off, or set, using the Function Code with the Master User code as authorization 
for changing or setting the function. A Function Code is a 2-digit code that is associated to a particular setting. 
Each Function Code has a default, or standard setting, which is in the lock when there have been no changes 
or after a Function Reset (F99) has been executed. They are as follows. 

 

Function Code List

 

   

         

Enable=1, Disable=0 

 

Function 

 

Function Description 

Setting 

Range 

 

Default 

01 

Time Delay Mode 

Enable/Disable 

1 or 0 

02 

Set Time Delay Period 

1 to 99 

10 

03 

Set Open Period 

1 to 9 

10 

Multiple User Mode 

Enable/Disable 

1 or 0 

11 

Add/Enable a User Combo 

1 to 8 

 

12 

Disable a User Combo 

1 to 8 

 

13 

Disable All Users 

 

20 

Duress Mode 

Enable/Disable 

1 or 0 

30 

Dual Combo Mode 

Enable/Disable 

1 or 0 

31 

Enable/Disable Two Subordinate Combos Opening 

1 or 0 

40 

Armored Car Time Delay Bypass 

Enable/Disable 

1 or 0 

41 

Enable/Disable Subordinate Authorization of TDL Bypass 

1 or 0 

50 

External Control Port 

Enable/Disable 

1 or 0 

60 

Subordinate User Combo Change 

Enable/Disable 

1 or 0 

99 

Reset All 

Functions to Default settings 

 

 

Combination Change Examples 

The Master Combo is 159260 and you wish to change it to 918273. Do the following: 

C-#-0-#-159260-#-918273-#-918273-# 

or  C-#-159260-#-918273-#-918273-# 

User 5’s combination is 342312 and you wish to change it to 768798 

C-#-5-#-342312-#-768798-#-768798-# 

User 5’s combination is unknown and you wish to set it to 768798, the Master Combo is 159260 

C-#-5-#-159260-#-768798-#-768798-# 

Содержание ESL20XL











Отзывы: