manualshive.com logo in svg

Amina AIW150i, Руководство по установке

Поделиться
Скачать
Amina AIW150i Скачать руководство пользователя страница 31

Warranty information

Limited Warranty:

The Amina Evolution Series speakers are designed to operate reliably for many years. Correctly 
installed in accordance with these instructions, Amina warranties the Evolution Series speakers 
against defective materials and workmanship for a period of five years in commercial 
applications and ten years in residential applications.

At the end of the speakers useful life and in compliance with the European directive on waste 
electrical and electronic equipment (WEEE), this product is to be returned to your supplier, or 
directly to Amina for recycling. If you have any questions please contact Amina Technologies 
Ltd.

* Please refer to our full warranty statement for details, available 

on our website, or 

alternatively contact Amina Technologies via email.

Important Note: 

This product has not been certified to European Construction Products 

Directive  EN 54-24 and therefore must not be used in voice evacuation systems located within 
the European Union.

Copyright information

 

This document is Copyright of Amina Technologies Ltd, 2015
Easi-fill is a registered trademark of British Gypsum Ltd
Amina is a registered trademark of Amina Technologies Ltd

28

  

WARNING:

No attempt should be made to install this product within existing building structures unless you 
are certain that no electric cables, water pipes, gas pipes or supporting joists will be cut through.

 

FIRE PROTECTION:

When making an intrusion into an internal wall or ceiling to install an Amina loudspeaker be sure 
to check the appropriate regulations pertaining to the required fire rating. Depending on the 
location of the intrusion and the applicable regulations it may be necessary to build in or install 
additional fire rated components or products to surround the speaker and back box. Amina 
Technologies take no responsibility for the correct specification and installation of any such fire 
protection system that is required behind their speakers.

Содержание AIW150i

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды