AMG AMG4784E Скачать руководство пользователя страница 8

AMG Systems Ltd. reserves the right to make changes to this 
document without notice. The information herein is believed to 
be accurate. No responsibility is assumed by AMG for its use.  

Page 8 of 8 

AMG4784E Instruction Sheet D32046-
00 
 

 

 

Physical Information 

Dimensions 

Height................................................... 112mm 
Width .................................................... 170mm (excluding connectors) 
Depth ................................................... 70mm 
Weight .................................................. 750grams 
 

 

Mounting Details 

The AMG unit is supplied with a clip-on mounting bracket which should be attached to a panel or wall 
using 2 off 4.0mm screws. The unit is clipped into the mounting bracket, and is then held firmly in 
position.  
 

 

Removal / replacement from / to the Case 

Note: - The AMG unit PCB's are static sensitive. Handle with proper care and use normal electrostatic 
discharge (ESD) procedures. Use properly grounded protection (for example, wrist straps) when 
handling the PCB.  
 
To remove units from the case to access the data expansion boards and the daughter boards, remove 
the 2 or 4 fixing screws on the rear panel and slide the PCB's out of the case.  
Ensure that the fibres do not snag or get trapped.  
 
To replace the PCB's into the case, slide the PCB's gently into the case aligning the boards with the 
appropriate slots. Ensure that the fibre do not snag or get trapped. 
 
 

 

Safety 

AMG Optical Fibre Products use Class 1 laser systems in accordance with EN 60825-2:2000. 
 
It is always advisable to follow good practice when working with optical fibre systems. This includes: 
 

 

Do not stare with unprotected eyes or with any unapproved collimating device at fibre 

ends or connector faces, or point them at other people. 

 

Use only approved filtered or attenuating viewing aids 

 
For other safety issues and advice on good practice associated with optical fibre systems, please see 
EN 60825-2:2000 or your local safety officer. 
 
 

 

Maintenance and Repair 

There are no user serviceable parts within AMG products. See unit data sheet for full specification. 
 
In case of problem or failure, please call your local support centre or contact:  

AMG Systems Ltd.

 at  

3 The Omega Centre, Stratton Business Park, Biggleswade, Beds., SG18 8QB, UK. 
 
 

Phone    

 

+44 (0) 1767 600 777 

 

Technical Support  

+44 (0) 1767 604 491  

 

Email    

 

[email protected] 

 

Содержание AMG4784E









Отзывы: