AMG AMG4784E Скачать руководство пользователя страница 4

AMG Systems Ltd. reserves the right to make changes to this 
document without notice. The information herein is believed to 
be accurate. No responsibility is assumed by AMG for its use.  

Page 4 of 8 

AMG4784E Instruction Sheet D32046-
00 
 

 

 

Connections 

Video Output Connections 

No. of channels .................................... 8 
Connectors .......................................... 75 ohm BNC Socket. 
Output Impedance ............................... 75 ohm terminated. 
Output Level ........................................ 1 Volt p-p nominal 
Frequency Response ........................... 10Hz to 7MHz. 
 

 

Optical Connections 

PRIMARY OPTO OUT

 

Connector ............................................ LC/PC 
Primary Optical Launch Power ............ -5dBm 
Wavelength .......................................... 1310nm 
Optical Fibre ........................................ Singlemode 
 

PRIMARY OPTO IN

 

Connector ............................................ LC/PC 
Primary Optical Sensitivity ................... -22dBm 
Wavelength .......................................... 1310nm 
Optical Fibre ........................................ Singlemode 
 

 

Power Connection 

Connector Type ................................... 2.1mm screw lock long power jack 

– centre positive  

Connector Partno. ................................ Switchcraft S761K, AMG G16125-00 
Supply Voltage ..................................... 13.5 to 18.0 Volts DC.  
Maximum Power  ................................. 5 Watts 
 

 

Ethernet Connection 

Ethernet Data Connector  .................... RJ45 
Interface ............................................... Auto-negotiation up to 100BASE-TX full duplex 
Ethernet Data Rate .............................. Maximum 50Mbits/s total Ethernet traffic on fibre 
 

 

Data and Audio Channel Connections 

DATA CHANNEL A

 

Data Channel A ................................... 1 channel 
Data Connector .................................... RJ45 
Channel A Interface ............................. On Board Data Interface 

– RS232, RS422 or RS485. Selected 

by slide switch above the RJ45 connector. 
 

 

RS232 

– switch position - high (closest to BNC connections) 

 

RS422 

– switch position – middle 

 

RS485 

– switch position – low (furthest from BNC connections) 

 

DATA CHANNEL B

 

Data Channel B ................................... Not Present 
 
 

 

Содержание AMG4784E









Отзывы: