Ametek Land LSP Ex System Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 48

Ametek Land LSP Ex System Скачать руководство пользователя страница 23

Page 13

User Guide

LSP Ex System for Zone 22

Linescanner Head

2 Installation

2.1 Introduction

The equipment specified in this User Guide must be operated, maintained

and serviced by suitably trained personnel, capable of carefully following the

procedures, warnings and guidelines given. It is advisable that all User Guides

and Installation Guides associated with LSP System equipment should be read

thoroughly and be kept readily available.
Refer to

ATEX Compliance Information

for safe installation of this equipment.

Caution

Ensure that the LSP Head is mounted securely, in a location where the

effects of vibration, dust and fumes are kept to a minimum. Ensure that the

scanning sight path is not obscured.

The LSP10, 20 & 21 have a focus distance factory set at 2000mm / 79 in.

Refer to Section 2.2 for details of how to change the focus distance.

Choose a mounting location which minimises external heating of the

scanner.

If the instrument is to be used in environments where gases resulting from

combustion are present, contact Land Instruments so that the application

can be fully assessed before you install the scanner.

«
...
21
22
23
24
25
...
»

Содержание Land LSP Ex System

















































Отзывы:

Нет отзывов