background image

 

GUPS 2400A

–107 Operation Manual 

4-1 

SECTION 4

 

 MAINTENANCE 

4.1

 

Introduction 

This section contains general information about maintenance of the GUPS 2400A-107. There 
are no adjustments accessible to the user. 

 

WARNING

 

Hazardous voltages are present when operating this equipment.  Please 
read the SAFETY NOTICE on page 

Error! Bookmark not defined.

 prior 

to installation, operation, or maintenance.

   

 

4.2

 

Service Information 

Questions concerning the operation, repair or service of this instrument should be directed to 
the nearest Elgar representative or to the Elgar Service Department, Elgar Electronics 
Corporation, 9250 Brown Deer Road, San Diego, CA 92121-2294. Include the model number 
and serial number in any correspondence concerning this instrument. DO NOT return the unit 
to the factory without prior authorization. 

4.3

 

Spare and Repair Parts 

When ordering spare parts or repair parts, specify the part name, part number, component 
value and rating, and the Elgar part number, if available. If complete assemblies are required, 
contact the Elgar Service Department.  

Specify the assembly part number as marked on the assembly and the unit model number, 
GUPS 2400A-107, when ordering. 

4.4

 

Periodic Maintenance 

The only maintenance required for this instrument is to periodically remove and clean or replace 
the front panel fan filter.  

The amount of time between cleaning is dependent on the environment in which the unit  
is used. Dust and dirt accumulation in the air filter can cause restricted air flow and subsequent 
overheating or reduced life on the internal components and batteries.   

Содержание GUPS 2400A-107





































Отзывы: