Ametek 0 LAND LSP HD 61 Скачать руководство пользователя страница 22

Страница: 22 / 42

Page 16

User Guide

LSP

Linescanner Head

3 Services

3.1 Electrical connections: Cable requirements

The connection between the Landscan LSP

Head and Landscan power supply units is

via an Ethernet cable.

Three pre-wired cable assemblies are available from LAND:

AMETEK Land

Part Nº

Length

Sheath

material

Ambient limit

Overall

diameter

805038

15m / 49ft

105°C / 221°F

7mm / 0.26in

804977

15m / 49ft

Teflon

200°C / 392°F

7mm / 0.26in

807087

30m / 98ft

105°C / 221°F

7mm / 0.26in

CAUTION

Never disconnect the scanner cable whilst the scanner is powered. Doing so

could damage other devices on the same TCP/IP network. Always turn off

power at the Power over Ethernet PSU prior to disconnecting the scanner cable.

Note

The scanner end of the cable is labelled 'Scanner' and is a right-angled M12

'D-coded' Ethernet connector.

The power supply end of the cable is a straight M12 'D-coded' Ethernet connector.

3.1.1 Power supply units

•

807105 LSP

Power Over Ethernet Supply Module

•

805037 LSP

PSU

•

805140 LSP

Service Panel

3.1.2 Default Network Settings

IP Address: 10.1.10.100
Subnet: 255.255.0.0

Each scanner is supplied with the IP address set to the default of 10.1.10.100. There is

a switch on the digital PCB that allows the last digit of the IP address to be changed.
If the switch is set in position 0, the last digit will be configured by software (this is the

default.)
If the switch is in any other position (7 for example), then the address will become

10.1.10.107, with all the other digits set in the software. Software is configured via

the Landscan browse utility (Refer to the help file/user documentation supplied with the

software).
A maximum of 4 clients may be connected to the scanner at one time.

Содержание 0 LAND LSP HD 61











































Результаты поиска

Содержание 0 LAND LSP HD 61

Отзывы:

Похожие инструкции для 0 LAND LSP HD 61

Бренды по названию

Популярные бренды

Ametek 0 LAND LSP HD 61, Руководство пользователя

Результаты поиска

Содержание 0 LAND LSP HD 61

Отзывы:

Похожие инструкции для 0 LAND LSP HD 61

Бренды по названию

Популярные бренды