American Water Heater DIRECT VENT GAS WATER HEATER Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 40

background image

18

Installation (Vent-Air Intake System Installation) continued-

5. Insert the straight end of the three (3) inch

(7.6 cm)

diameter elbow into

the flue reducer until firmly seated and oriented in the correct direction.
With a 1/8 inch diameter drill bit (not supplied), drill three (3) holes, 120

o

apart, through the flue reducer into the three (3) inch

(7.6 cm)

diameter

elbow. Fasten with three (3) #8 sheet metal screws (supplied). Using
the supplied special RTV silicone sealant, apply a sufficient amount to
seal the joint (See Figure 8).

Figure 8

6. Place the straight end of the five (5) inch

(12.7 cm)

diameter elbow over

the three (3) inch

(7.6 cm)

diameter elbow and plenum collar until seated

on top of the plenum box. Make certain that the five (5) inch

(12.7 cm)

diameter elbow is oriented in the same direction as the three (3) inch

(7.6 cm)

diameter elbow and both are oriented in the correct direction.

Drill three (3) 1/8 inch diameter holes, 120

o

apart, through the five (5)

inch

(12.7 cm)

diameter elbow into the plenum collar. Fasten with three

(3) #8 sheet metal screws (supplied) (See Figure 9).

IMPORTANT

The following instructions detail the installation of the standard
horizontal vent-air intake kit supplied with the water heater.

«
...
16
17
18
19
20
...
»

Содержание DIRECT VENT GAS WATER HEATER









































Отзывы:

Нет отзывов

Похожие инструкции для DIRECT VENT GAS WATER HEATER

Бренд: LAMBORGHINI CALOR Страницы: 15

Бренд: Radiatori 2000 Страницы: 2

Бренд: veito Страницы: 28

Бренд: Wangen Страницы: 72

Бренд: Jata Страницы: 32

Бренд: Liberty Pumps Страницы: 16

Ingenio VM 050 D400-3-E

Бренд: Atlantic Страницы: 69

Бренд: Harvia Страницы: 44

Бренд: Pfeiffer Vacuum Страницы: 40

Бренд: Xylem Страницы: 20

Бренд: Talhu Oy Страницы: 11

Бренд: UNITED Страницы: 5

Бренд: EdgeStar Страницы: 13

Бренд: Global Industrial Страницы: 3

Бренд: Waterous Страницы: 7

Бренд: CleanCraft Страницы: 22

Бренд: vacuubrand Страницы: 72

Бренд: Mark Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды