background image

M965074 REV.1.4

Certified to comply with ANSI A112.18.1

Installation

Instructions

MONOBLOCK LAVATORY

FAUCET with Speed Connect™ Drain

Adjustable Wrench

 Screwdriver

Channel Locks

Recommended tools

2555.101

Series

1

TOWNSQUARE™

To ensure that your installation proceeds smoothly-please read these instructions carefully 

before you begin.

Congratulations on purchasing your American Standard

faucet with Speed Connect drain, a feature found only 

on American Standard faucets.

*Your new American Standard faucet is designed to work only with the Speed Connect drain. 

Speed Connect Drain*

•  Fewer parts, installs in less time

•  Never needs adjustment

•  Guaranteed to seal properly the first time, every time.

COLLAR ON

MOUNTING NUT

8

2

4

3

1

9

1

INSTALL FAUCET

Turn off hot and cold water

supplies before beginning.

CAUTION

GROOVE

(FAUCET

BASE)

MOUNTING SURFACE

6

4

7

5

Installation less ESCUTCHEON PLATE:

Seat SEAL 

(1)

 into under side of FAUCET BASE 

(2)

.

Feed FAUCET SUPPLIES 

(3)

, MOUNTING STUD 

(4)

 and DRAIN

CABLE ASSEMBLY 

(8)

 through the mounting hole of lavatory or

mounting surface. 

Fig. B.

From below, push GASKET 

(7)

 and RETAINING WASHER 

(5)

 onto

MOUNTING STUD 

(4)

. Secure Faucet with MOUNTING NUT 

(6)

,

pulling faucet to front of sink, so SUPPLIES 

(3)

 rests against

mounting hole. Before final tightening, make sure collar on 

MOUNTING NUT 

(6)

 is seated into RETAINING WASHER 

(5)

.

Fig. C .

Adjust Faucet so that it is centered. Tighten MOUNTING NUT 

(6)

to complete faucet mounting.

Fig.

 

C.

Fig.

 

B.

Fig.

 

A.

Installation with ESCUTCHEON PLATE: 

Apply a light bead of plumbers putty

to underside of ESCUTCHEON PLATE 

(9)

 if mounting surface is uneven.

 

Place ESCUTCHEON

PLATE 

(9)

 onto sink or mounting surface.

 

Feed FAUCET SUPPLIES 

(3)

, MOUNTING

STUD 

(4)

 and DRAIN CABLE ASSEMBLY 

(8)

 through ESCUTCHEON PLATE and PUTTY

PLATE 

(9) 

and mounting hole of lavatory or mounting surface.

 Fig. A.

PUTTY

IF REQUIRED

Содержание TOWNSQUARE 2555.101 Series








Отзывы: