background image

M965074 REV.1.4

STOPPER INSTALLATION PROCEDURE

Locked Mode: 

Look at the Plastic Loop at the bottom of the Stopper and notice

that the Loop is on one side of the Stopper. 

Fig.

 

G.

To install the stopper in 

“Locked”

 mode, insert the Stopper into

the Drain so that the Plastic Loop is facing toward the 

rear

 of the

Sink and the American Standard logo is facing 

front

. Rotate

Stopper slightly if necessary so that the Stopper slides all the

way down.

Fig.

 

G.

Re-install the Cam into the Drain, rotating the Cam if necessary

to make sure it is fully inserted. 

Fig.

 

J.

Re-install the Cam Cap, making sure the guide teeth are facing

outward. If the Cam Cap does not “snap” into place, then rotate

the Cam to make sure it is fully inserted. 

Fig.

 

K.

Re-attach Cable. See “CABLE ADJUSTMENT PROCEDURE” in

Troubling Shooting Guide to complete installation. Stopper will be

in 

“Locked”

 mode and not be removable.

Unlocked Mode: 

Look at the Plastic Loop at the bottom of the Stopper and notice

that the Loop is on one side of the Stopper. 

Fig.

 

H.

To install the stopper in 

“Unlocked”

 mode, insert the Stopper into

the Drain so that the Plastic Loop is facing toward the 

front

 of the

Sink and the American Standard logo is facing 

rear

. Rotate Stopper

slightly if necessary so that the Stopper slides all the way down.

Fig.

 

H.

Re-install the Cam into the Drain, rotating the Cam if necessary

to make sure it is fully inserted. 

Fig.

 

J.

Re-install the Cam Cap, making sure the guide teeth are facing

outward. If the Cam Cap does not “snap” into place, then rotate

the Cam to make sure it is fully inserted. 

Fig.

 

K.

Re-attach Cable. See “CABLE ADJUSTMENT PROCEDURE” in

“Troublingshooting Guide” to complete installation. Stopper will be

in 

“Unlocked”

 mode and removable

.

Fig.

 

J.

Fig.

 

K.

INSTALL

CAM CAP

CAM

INSTALL CAM

The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be

removed) or “Unlock” Mode (Stopper is removable).

Unlocked Mode

LOOP TOWARD

FRONT OF SINK

180˚

LOGO

DRAIN

Fig.

 

H.

Locked Mode

(Vandal Proof)

LOGO

DRAIN

Fig.

 

G.

LOOP TOWARD

REAR OF SINK

6

Содержание TOWNSQUARE 2555.101 Series








Отзывы: