background image

7

TIPS FOR REMOVING YOUR OLD DRAIN:

Loosen nuts on P-Trap using channel locks. Suggest spraying nuts with spray lubricant to loosen any corrosion or

debris that may have built up. Remove P-Trap half from Tailpiece. Use bucket to catch any residual water in P-trap.

Unthread Pivot Rod Nut from Drain Body and remove. Pull Stopper out from Drain Body.

Loosen Mounting Nut as far down as it will go. Push Drain Body up into Sink and unthread Flange from Drain Body.

Remove Drain Body from below sink.

Unthread Tailpiece from Drain Body.

Loosen and remove Mounting Nut and Gasket on Drain Body using channel locks. Suggest spraying nut with spray

lubricant to loosen any corrosion or debris that may have built up. Push Drain Body up into the Sink and remove.

Note: 

If Drain body rotates while loosening Mounting Nut, insert a screw driver into overflow hole to prevent Drain 

Body from rotating while Mounting Nut is removed. 

Adjustable Wrench

Phillips Screwdriver

Channel Locks

Recommended tools

METAL OR PLASTIC TWO PIECE

DRAIN BODY 

 

METAL DRAIN BODY WITH

PLASTIC TAILPIECE 

PLASTIC DRAIN BODY

WITH PLASTIC TAILPIECE 

UNTHREAD

FLANGE

STOPPER

WHEN DRAIN IS REMOVED FROM ABOVE SINK

WHEN DRAIN IS REMOVED

FROM BELOW SINK

MOUNTING

NUT

MOUNTING

NUT and

GASKET

METAL

DRAIN

BODY

PLASTIC

DRAIN BODY

PLASTIC

TAILPIECE

P-TRAP

HALF

PIVOT

ROD NUT

PIVOT

ROD NUT

SINK

STOPPER

SCREWDRIVER

STOPPER

MOUNTING

NUT and

GASKET

METAL OR

PLASTIC

DRAIN BODY

FINISHED

WALL

FINISHED

WALL

FINISHED

WALL

PLASTIC

TAILPIECE

PIVOT

ROD NUT

SINK

SINK

P-TRAP

HALF

P-TRAP

HALF

Most existing drains can be removed quickly and easily with only a pair of channel-

lock pliers or a wrench. However, there may be situations where it is difficult to 

remove your old drain or determine how the drain is disassembled. Depending upon 

the existing Drain in your sink, it is either removed from above or below the sink. 

The illustrations below show some typical drain installations and how they are 

disassembled from the sink.

The following tips can help with some of the more common challenges in drain removal: 

For Drains that are removed from below Sink:

For Drains that are removed from above Sink:

M 9 6 8 6 7 2   R e v .   1 . 1

Содержание Symphony 4508S








Отзывы: