American Hearth Intermittent Pilot ADVCX36FP70N-2 Скачать руководство пользователя

Страница: 10 / 68

35010-2-1015

Page 10

Clearances

WARNING

This fireplace is not been tested nor approved to have a television

or other electrical appliance installed above it.

Clearance from bottom of fireplace to ceiling is 84”

Clearance from side of fireplace to adjacent sidewall is 6”.

Television Considerations

Installing a television above a fireplace has become increasingly

popular; however, the area above any fireplace gets hot and most

TV manufacturers recommend against placing their products near

a heat source.

If you install a television above this fireplace, Empire Comfort Sys

tems accepts no responsibility for damage or injuries. Follow the

television manufacturer’s installation instructions, including any

recommendations regarding proximity to heat sources.

If you have a TV above your fireplace, turn off the fireplace and

let it cool completely before servicing or touching any buttons on

the TV.

CLEARANCES

Do not attach combustible material to the mantel of your fireplace.

This is a fire hazard.

Figure 5

Note: Generic Firebox shown.

No greeting card, stockings or ornamentation of any type should be

placed on or attached to the fireplace. This is a heating appliance.

The flow of heat can ignite combustibles.

Figure 6

Note: Generic Firebox shown.

COMBUSTIBLE MATERIAL

Figure 3

Figure 4

Содержание Intermittent Pilot ADVCX36FP70N-2





































































Результаты поиска

Содержание Intermittent Pilot ADVCX36FP70N-2

Отзывы:

Похожие инструкции для Intermittent Pilot ADVCX36FP70N-2

Бренды по названию

Популярные бренды

American Hearth Intermittent Pilot ADVCX36FP70N-2, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание Intermittent Pilot ADVCX36FP70N-2

Отзывы:

Похожие инструкции для Intermittent Pilot ADVCX36FP70N-2

Бренды по названию

Популярные бренды