REV. 4-6-2010
Page 8 of 11
2. When the continuous pilot switch is in the OFF position and the appliance on/off switch is turned ON the pilot will
spark and light, and when the appliance on/off switch is turned OFF the pilot will shut OFF when the main burner
shuts OFF.
3. When the continuous pilot switch is in the ON position and the appliance on/off switch is turned ON the pilot will spark
and light, when the appliance on/off switch is turned OFF the pilot will stay ON when the main burner shuts OFF. This
setting is generally used in Cold Climate to keep the firebox warm.
4. The CONTINUOUS pilot mode can also be activated by an (Optional) hand held Remote Control.
REMOTE CONTROL FEATURE:
The (AF-4000 MOD) module has a built in remote control receiver this allows the user
to program a hand held remote transmitter, wireless wall mount thermostat or wireless wall mount switch to the appliance
at any time during or after installation of the appliance.
1. There is a switch located on the right side of the (AF-4000 MOD) module that reads REMOTE/OFF. Note: Figure #9
2. When the remote/off switch is in the OFF position the appliance will operate from an appliance mounted rocker switch
or wall switch connected to the (2) BROWN wires on the (AF-4000 MOD) Module.
3.
When the remote/off switch is in the REMOTE position the appliance will operate from the (Optional) Remote Control
transmitter wireless wall mount thermostat or wireless wall mount switch.
Note:
The AF-4000 MOD must be programmed to the (Optional) Remote Control transmitter wireless wall mount
thermostat or wireless wall mount switch.
1. To program the AF-4000 MOD (Make sure the system is power) locate the learn button on the AF-4000 MOD (Note
Figure #10) press and release the learn button there will be a beep sound from the AF-4000 MOD then press any key
on the remote transmitter. Once the AF-4000 MOD internal receiver accepts the transmitter code there will be a series
of confirming beeps.
2.
The remote system is ready for use.
AF-4000 MOD (Options)
The AF-4000 MOD can be powered by two (2) different scores (1) is a standard 110 volt AC to 6.0 volt DC adaptor. This
adaptor is connected to the AF-4000 MOD by connecting the (2) 1/4’ female terminals from the adaptor to the (2) 1/4”
male terminals located on the AF-4000 MOD marked (power).
Using the 6.0 volt adaptor (only) without using the AF-4000 BP battery pack the system will not have a back up power
scores during a power outages.
Wiring The (AF-4000 BP) Battery Pack
1. Locate the (AF-4000 BP) battery pack in an area that that will not exceed an ambient temperature of 130º F (Batteries
exposed to temperatures above 120ºF will drain voltage and shorten battery life).
2. Locate the AUX connection and the optional Hi/Lo wire connections on the (AF-4000 BP) battery pack Note: Figure
#13.
3. Locate the wire connections on the (4) pin connector wiring harness and the solenoid or DC motor drive wiring
harness shown in Note Figure #13.
4. Install (4) AA alkaline batteries in the (AF-4000 BP) battery pack.
5. Plug one of the (4) pin female connector on the (AF-4000 BP) battery pack wiring harness into the (4) pin male
connector located on the back of the battery pack Note location shown in Figure #13.
6. Plug the other (4) pin male connector on the (AF-4000 BP) battery pack wiring harness into the (4) pin female AUX
connector located on the (AF-4000 MOD) module shown Note location shown in Figure #10.
7. If the model of AF-4000 electronic control valve has a Hi/Lo solenoid or DC motor drive use the solenoid or DC motor
drive wiring harness shown in Figure #13
Note
:
If the Hi/Lo Step Motor (Model AF-4000MOT) has been selected the this requires a unique operating
control transmitter and receiver specifically set-up for the desired Hi/Lo increments required by the burner
installed in the appliance that the AF-4000 valve system is used on.
Wiring The Optional Hi/Lo
1. Connect the striped ends of the RED and BLACk wires on solenoid or DC motor drive wiring harness to the screw
terminals located on ther top of the (AF-4000 BP) battery pack Note: location in Figure #13
2. Connect the (2) 1/4” female terminals on the solenoid or DC motor drive wiring harness to the matching color (RED &
BLACK) 1/4” male terminals on the Hi/Lo solenoid or the Hi/Lo DC motor drive. Note: locations in Figure #8 & #13.
3. Note the Latching Solenoid mode and DC Motor Drive mode switch located on the front of the (AF-4000 BP) battery
pack in Figure #13.
f i r e - p a r t s . c o m
