background image

 

ADACSNET USB CONTROL MODULE 

8200-0310-01, REV. B 

INSTALLATION GUIDE 

6 of 6

 

Declarations 

Regulatory Compliance 

EMC........................................................47 CFR, Part 15 
 ICES-003 
 EN55022 
 CISPR 

22 

Safety ................................................................. UL 1950 
 

CSA C22.2 No 950 

 

TUV Rhienland EN60950 

 IEC 

950 

FCC COMPLIANCE:

 This equipment complies with Part 15 

of the FCC rules for intentional radiators and Class A digital 
devices when installed and used in accordance with the 
instruction manual. Following these rules provides reasonable 
protection against harmful interference from equipment 
operated in a commercial area. This equipment should not be 
installed in a residential area as it can radiate radio frequency 
energy that could interfere with radio communications, a 
situation the user would have to fix at their own expense. 

EQUIPMENT MODIFICATION CAUTION:

 Equipment 

changes or modifications not expressly approved by 
Sensormatic Electronics Corporation, the party responsible for 
FCC compliance, could void the user's authority to operate the 
equipment and could create a hazardous condition. 

Other Declarations 

Thank you for using American Dynamics products. We 
support our products through an extensive and worldwide 
network of dealers. The dealer, through whom you originally 
purchased this product, is your point of contact if you have a 
need for service or support. Our dealers are fully empowered 
to provide the very best in customer service and support. 
Dealers should contact American Dynamics at 
(800) 507-6268 or (561) 912-6259 or on the web at 
www.americandynamics.net. 

WARRANTY DISCLAIMER:

 Sensormatic Electronics 

Corporation makes no representation or warranty with respect 
to the contents hereof and specifically disclaims any implied 
warranties of merchantability or fitness for any particular 
purpose. 

NOTICE: 

The information in this manual was current when 

published. The manufacturer reserves the right to revise and 
improve its products. All specifications are therefore subject to 
change without notice. 

LIMITED RIGHTS NOTICE:

 For units of the Department 

of Defense, all documentation and manuals were developed at 
private expense and no part of it was developed using 
Government Funds. The restrictions governing the use and 
disclosure of technical data marked with this legend are set 
forth in the definition of “limited rights” in paragraph (a) (15) 
of the clause of DFARS 252.227.7013. Unpublished - rights 
reserved under the Copyright Laws of the United States. 

TRADEMARK NOTICE:

 

American Dynamics

 and 

Sensormatic

 are trademarks or registered trademarks of 

Sensormatic Electronics Corporation. Other product names 
mentioned herein may be trademarks or registered trademarks 
of Sensormatic or other companies. 

COPYRIGHT:

 Under copyright laws, the contents of this 

manual may not be copied, photocopied, reproduced, 
translated or reduced to any electronic medium or machine-
readable form, in whole or in part, without prior written 
consent of Sensormatic Electronics. 

MDR 03/2004 

Содержание ADACSNET







Отзывы: