AD1684B
CONNECTIONS
Pan/Tilt and Lens Connections
The Receiver connection to a Pan/Tilt and a motorized Lens is
with a 10-pin connector. This connector is located on the left
side of the PCB and is labeled J7 (see Figure 1, page 2). When
the unit is set for dual operation (see Setup, page 2) a second
10-pin connector labeled J6, located on the right side of the
PCB opposite to J7, is used for the second Pan/Tilt and Lens.
Table 5 (page 8) lists the pin designations from the Receiver to
the Pan/Tilt and Lens and provides space for the installer to
record the pinouts for the specific installation. Match the
Pan/Tilt and lens pinouts from the manufacturer’s installation
manuals to Table 5 (on the following page).
Mating 10-pin screw-terminal connectors are provided for each
PCB connector (see Figure 5). The connector terminals accept
wire gauge sizes from 22-AWG to 14-AWG, stripped 1/4"
(6mm) from the end.
The following are the pin definitions for pan/tilt drive:
• The voltage on the pin marked "LEFT" physically pans the
camera view to the left.
• The voltage on the pin marked "RIGHT" physically pans
the camera view to the right.
• The voltage on pin marked "UP" physically tilts the camera
lens view upward.
• The voltage on the pin marked "DOWN" physically tilts the
camera lens view downward.
BEFORE STARTING:
1. Check the power line to verify that the power is off.
2. Open the Receiver and locate the Pan/Tilt and Lens
connector J7 on the left side of the unit. For dual-channel
operation, also locate connector J6.
WIRING INSTRUCTIONS:
3. Pass the wire through the bushing to the Pan/Tilt and Lens
connector, do not tighten bushing.
4. Strip the Pan/Tilt and Lens wires 1/4" (6mm) from the end.
Pan/Tilt:
5. Insert the PAN LEFT wire of the Pan/Tilt Unit into the
screw-terminal connector pin location for Pan LEFT.
6. Insert the PAN RIGHT wire of the Pan/Tilt Unit into the
pin location for Pan RIGHT.
7. Insert the TILT UP wire of the Pan/Tilt Unit into the pin
location for Tilt UP.
8. Insert the TILT DOWN wire of the Pan/Tilt Unit into the
pin location for Tilt DOWN.
9. Insert the Pan/Tilt AC COMMON wire of the Pan/Tilt Unit
into the pin location for AC COMMON.
10. Insert the cable SHIELD of the Pan/Tilt cable into the pin
location for SHIELD on connector J4 or J3 (use J4 for a
Pan/Tilt connected to J7; use J3 for a second Pan/Tilt
connected to J6).
Motorized Lens:
11. Insert the IRIS wire of the motorized Lens unit into the pin
location for IRIS.
12. Insert the FOCUS wire of the motorized Lens unit into the
pin location for FOCUS.
13. Insert the ZOOM wire of the motorized Lens unit into the
pin location for ZOOM.
14. Insert the Lens COMMON wire of the motorized Lens unit
into the pin location for DC GROUND.
Note: DO NOT connect the LENS COMMON to the
PAN/TILT COMMON.
15. Insert the SHIELD of the Lens cable into the pin location
for SHIELD on connector J4 or J3 (use J4 for a lens
connected to J7; use J3 for a second lens connected to J6).
16. Remove any excess cable and tighten the bushing.
17. Insert the screw-terminal connector into the J7 connector.
For dual-channel operation, repeat steps 3 through 17 for
Channel B, using connector J6 on the PCB.
Refer to the Typical System Connections illustration, page
C-4, for Pan/Tilt connections.
7
HOLD DOWN SCREWS
Figure 5 - Screw-Terminal Connector
Содержание AD1684B
