American Dryer Corp. Gas-HSI ADG-78 II Скачать руководство пользователя | Manualshive

Страница: 40 / 45

background image

36

90 DAYS

1. Remove lint from around basket (tumbler), drive motors, and surrounding areas.

2. Remove lint from gas valve burner area with a dusting brush or vacuum cleaner attachment.

3. Clean any lint accumulation in and around both the blower and drive motor casing openings.

NOTE

: To prevent damage, avoid cleaning or touching the hot surface ignitor assembly.

EVERY 6 MONTHS

Inspect and remove lint accumulation in customer furnished exhaust duct work system and from dryers
internal exhaust ducting.

NOTE: THE ACCUMULATION OF LINT IN THE EXHAUST DUCT WORK CAN

CREATE A POTENTIAL FIRE HAZARD.

NOTE

:

DO

NOT

OBSTRUCT THE FLOW OF COMBUSTION and VENTILATION AIR.

CHECK CUSTOMER FURNISHED BACK DRAFT DAMPERS IN THE EXHAUST
DUCT WORK. INSPECT and REMOVE ANY LINT ACCUMULATION WHICH
CAN CAUSE THE DAMPER TO BIND or STICK.

NOTE

: A back draft damper that is sticking partially closed can result in slow drying and shut-down of

the heat circuit safety switches or thermostats

NOTE

: When cleaning the dryer cabinet(s), avoid using harsh abrasives. A product intended for the

cleaning of appliances is recommended.

B. ADJUSTMENTS

7 DAYS AFTER INSTALLATION and EVERY 6 MONTHS THEREAFTER

Inspect bolts, nuts, screws, (bearing set screws), non-permanent gas connections (unions, shut-off valves,
orifices, and grounding connections). Motor and drive belts

should be

examined. Cracked or seriously

frayed belts

should be

replaced. Tighten loose V-belts when necessary. Complete operational check of

controls and valves. Complete operational check of

ALL

safety devices (door switches, lint drawer switch,

sail switch, burner and hi-limit thermostats).

«
...
38
39
40
41
42
...
»

Содержание Gas-HSI ADG-78 II














































Отзывы:

Нет отзывов

Похожие инструкции для Gas-HSI ADG-78 II

Spacemaker WSM2480

Бренд: GE Страницы: 12

Spacemaker GTUP270EMWW

Бренд: GE Страницы: 3

Бренд: BaByliss PRO Страницы: 44

Бренд: Conair Страницы: 2

Бренд: Vidal Sassoon Страницы: 4

Бренд: Frymaster Страницы: 3

Бренд: 4CR Страницы: 11

ADVANTAGE Series

Бренд: Amera Products Страницы: 2

Бренд: Mellerware Страницы: 26

Бренд: Solt Страницы: 2

Бренд: Kalorik Страницы: 62

Бренд: TriStar Страницы: 10

Бренд: Master Chef Страницы: 18

Бренд: Quincy Страницы: 17

Бренд: Modena Страницы: 20

commercial washer

Бренд: GE Страницы: 12

Бренд: GE Страницы: 4

Бренд: GE Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды