background image

14

To compensate for the use of registers or louvers used over the openings, this make-up air 

must be 

increased by

approximately thirty-three percent (33%).  Make-up air openings 

should not be

 located in an area directly near

where exhaust vents exit the building.

It is not necessary to have a separate make-up air opening for each dryer.  Common make-up air openings are
acceptable.  However, they 

must be

 set up in such a manner that the make-up air is distributed equally to 

ALL

the dryers.

EXAMPLE:

For a bank of four (4) dryers, two (2) unrestricted openings measuring 2 feet by 1-1/2 feet
(6 square feet) is acceptable.

Allowances 

must be

 made for remote or constricting passageways or where dryers are located at excessive

altitudes or predominantly low pressure areas.

IMPORTANT

:

M ake-up ai

r

 

must be

 provided from a source free of dry cleaning solvents fumes.

Make-up air that is contaminated by dry cleaning solvent fumes willresult in
irreparable damage the motors and other dryer components.

NOTE

:

Component failure due to dry cleaning solvent fumes wi

l

l

 

 

VOID THE WARRANTY.

Содержание Gas-HSI ADG-78 II














































Отзывы: